Dissertation > Excellent graduate degree dissertation topics show

Research on Metastable Pitting and Related Morpology of Pure Iron in NaNO2+NaCl Solution

Author: WangHu
Tutor: ZuoYu
School: Beijing University of Chemical Technology
Course: Materials Science
Keywords: Industrial pure iron Metastable pitting Current fluctuations Surface morphology
CLC: TG174
Type: Master's thesis
Year: 2004
Downloads: 75
Quote: 1
Read: Download Dissertation

Abstract


In this paper, dynamic sweep voltammetry , potentiostatic polarization method and electrochemical impedance spectroscopy study of pure iron in NaNO 2 NaCl system metastable pitting behavior , and comparison of carbon steel and stainless steel , the relationship between the discussed factors affect the metastable pitting formation and development , the polarization behavior of metastable pitting and sample surface conditions , and metastable hole pitting morphology current fluctuations . The main factors affecting industrial pure iron metastable pitting behavior the aggressive solution ion concentration , surface roughness , potential , and temperature ; stainless steel addition also affected by these factors , the metastable pitting behavior but also by surface inclusions is significantly affected , thereby causing these two materials pitting behavior difference . A number of industrial pure iron sample potentiodynamic polarization experiments found that the number of nucleation and the peak current of the metastable holes decreases with an increase in the number of polarization , E m and E b value increased ; polarization process every hole nucleation number increased with the rise of the potential ; influenced by multiple polarization more stainless steel than industrial pure iron and carbon steel large. Industrial pure iron , A3 steel and stainless steel fluctuations peak shape quite different reasons for this difference in solution passivation ability with the material itself . Industrial pure iron formation in the NaNO 2 the NaCl system early in the pits by a continuous shallow open holes , holes preferentially along the ground to form the trench direction . The formation and development of pitting by the surface roughness of the two stone page d two degree Shilun text impact , easier to form a rough surface active sites , trench width depth ratio w / d and the potential impact of pitting nucleation and development. Early pitting major impact by the former , while the latter is mainly controlled by potentiometer . Good corresponding relationship , indicating that the current fluctuations in the current time curve peaks and pits on the surface morphology is possible according to the number and amplitude of current fluctuation prediction material surface corrosion damage extent .

Related Dissertations

  1. Preparation and Characterization of Doped Cu3N Thin Films by Magnetron Sputtering,O484.1
  2. Silicon Carbon Nitride Thin Film Grown by Hot-Filament Chemical Vapor Deposition,TB383.2
  3. Porous silica hollow microspheres Preparation and release behavior of pesticides,TQ450.1
  4. Study about the Characteristic of Poplar Surface by the Treatment of Low Temperature Plasma,TS652
  5. Phosphating and Cathode Electrophoretic on the AZ61 Magnesium Alloy,TG174.4
  6. The Evolvement of Quartzs and Phytoliths in Basalt-Derived Chronosequence Soils in Tropics Area of China,S153
  7. Non-contact On-line Measurement of the Micro-topography of Ultra-precision Machined Surface,TH744
  8. Photo-graft surface morphology and distribution of graft chain,TQ316.3
  9. Theoretical and Experimental Studies on the Ultra-Precision Face-milling of Engineering Ceramics,TQ174
  10. High-speed milling surface topography simulation and experimental study,TG54
  11. Fe, Co, Ni, Mn passivated porous silicon preparation, surface morphology and photoluminescence study,TN305
  12. Study on Synthesis of Novel Liquid Crystal Compounds and their Application in Anticoagulative Materials,R318.08
  13. Study on the Preparation and Properties of Smooth Diamond-like Carbon Films,O484.1
  14. The Development of Brazed CBN Wheel with Addition of Rare-earth in Brazing Alloy,TG580.6
  15. Study on the Fixed Abrasive Polishing Pad for Micro-electronics Manufacturing,TG580.6
  16. Sampling and Assessment for Surface Topography of Carbon Fibre Composite Workpieces,TB332
  17. Microstructure and Properties of Electroplating Aluminum Coating Treated by Micro-arc Oxidation Process on Q235 Steel,TG174.4
  18. 2D Waveletanalysis on KDP Crystal Surface Micro-Topography by SPDT,TG506.1
  19. Electrical Sliding Wear of A12O3/Cu Composite Used in Contact Wire,TB333
  20. Micro-Topography Simulation on Turn-Milling Surface and Its Cutting Parameters Analysis,TG54
  21. Gansu Onagraceae Plant Classification,Q949

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > Metal corrosion protection,metal surface treatment > Corrosion control and protection
© 2012 www.DissertationTopic.Net  Mobile