Dissertation > Excellent graduate degree dissertation topics show

Research of Sheet Metal Forming Based on Defence Node Algorithm

Author: HongHaiJin
Tutor: LiGuangYao
School: Hunan University
Course: Vehicle Engineering
Keywords: Contact Defence node algorithm Sheet metal forming Springback Optimization design
CLC: TG386
Type: Master's thesis
Year: 2011
Downloads: 12
Quote: 0
Read: Download Dissertation

Abstract


Sheet metal forming is a very important technology in automotive manufacturing.Most automotive panels are obtained by sheet metal forming.In sheet metal forming process, the external forces which make deformation ofsheet metal are blank holder forces and contact forces. Blank holder forces are fixed,therefore, the calculation of contact forces directly affect the simulation results offorming process. Internationally accepted calculation methods of contact forces are:①penalty function method;②Lagrange multiplier method. Penalty function methodis an approximate method which allows contact borders penetrate each other. It makesrelationship between contact force and penetration by penalty parameter. Penaltyparameter multiply penetration is the size of contact force. This method is simple andless calculation, but is difficult to select penalty parameter. To make less borderpenetration, we should choose large value of penalty parameter which will increasethe system stiffness, lead to increase the system frequency and affect the critical timestep of the system. Lagrange multiplier method does not allow the borders topenetrate each other, and is an accurate calculation method of contact force. But it isincompatible with the explicit algorithm, and requires special numerical treatment. Inthis thsis, we choose the defence node algorithm which is proposed by ProfessorZhong Zhihua to calculate contact force. It can calculate contact force accurately, canuse Lagrange multipier method to satisfy constraints accurately, and also can avoid tosolve simultaneous equations.Around thesubject of the defence node algorithm inapplication of sheet metal forming, contents of this thesis are as follows:(1) Finite element program of sheet metal forming based on defence nodealgorithm was developed.(2) Tested and verified the advantages and disadvantages of the penalty functionmethod. These illustrated the necessity to use defence node algorithm to calculatecontact force.(3) Compared the calculation accuracy between developed program andcommercial softwares and experimental results. Verified the feasibility of theprogram.(4) Based on the developed program, an optimization design method based onmulti-island genetic algorithm is proposed to control springback. Calculation exampleshows that this method can better control springback.

Related Dissertations

  1. Study on Springback of High-Strength Steel Stamping,TG386
  2. Development of the Platform for Compressor Optimization Design and Aerodynamic Optimization Design in the Transonic Compressor,TH45
  3. Study on Contact Fatigue Life Based on Grease Variation with Temperature,TH117.22
  4. Investigation of Turbine S2 Stream Surface Direct Problem Aerodynamic Optimization Design,V235.11
  5. Influence of Nanostructure on Hydrophobic Properties at TiO2 Surface Studied by Molecular Dynamics Simulation,O614.411
  6. Fast Determination Method Research of Bisphenol A in Food Packing Material,TS206.4
  7. The Dynamic Performance Analysis of Oil Pumping Center and Structural Optimization of Improvement,TE933.1
  8. Finite Element Analysis and Optimization Design of a Tractor Cab,S219.02
  9. Medical Application of a Wireless Communication Platform Based on RFID and GPRS,R319
  10. The Research of Effective Learning Way for Primary and Secondary Schools,G632.0
  11. Equipment Research of the Ship Sewage Treatment,X703
  12. The Experimental Study on Effect of Different Low-power Laser Irradiation on Osseointegration of Dental Implants,R783.6
  13. Non- rigid body system kinematics and dynamics of the collision point,O313.3
  14. Axial fan blade vibration non-contact measurement,TD441.2
  15. FEA Analysis for Contact Roller of Sanding Machine,TS64
  16. Study of Optimization Design of Asymmetric and Much Support Floating Raft Isolation System,TB535.1
  17. Case Analysis of Road Traffic Accidents for Yindi Company against Yuanlong Company,D913
  18. Research on non contact vacuum technology cyclone type,TH138.9
  19. Study of the Friction and Adhesion Mechanism of Animal Foot-Pad Surface Morphology,TH117.1
  20. Research on Optimum Design of Plantary Gear Transmission Mechanism for Cutterbar,TH132.41
  21. Dynamics Analysis and Optimization Design of Hydraulic Excavator Working Equipment,TU621

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metal pressure processing > Cold stamping ( sheet metal processing) > Cold stamping process
© 2012 www.DissertationTopic.Net  Mobile