Dissertation > Excellent graduate degree dissertation topics show

Study on Tensile Properties of Bonded-metal-anchor Group for Post-installed Fastenings in Concrete Structures

Author: ZhouMeng
Tutor: ZhaoTingSheng; XuFuQuan
School: Huazhong University of Science and Technology
Course: Architecture and Civil Engineering
Keywords: Post-installed Fastenings Anchor Group Bonded-Metal-Anchor Tensile Test Failure Mode
CLC: TU37
Type: Master's thesis
Year: 2012
Downloads: 34
Quote: 0
Read: Download Dissertation

Abstract


Post-installed Fastening is a means of anchorage on existing buildings, includingexpansion anchors, undercut anchors, bonded metal anchors and bonded rebars. For itsreasonable load delivery, fast construction and other advantages, bonded metal anchors arewidely used. Anchor group is the most common form in practice, with greater differencesin mechanical properties compared with single anchor. Therefore, it is of greatsignificance on the study of anchor group.With the opportunity of modification of the Technical specification for post-installedfastenings in concrete structures, two groups of single anchor, double anchors, fouranchors, six anchors were tested and numerical simulated, which were described in detailas follows.(1)Research status at home and abroad was summarized, and the main factorsinfluencing the post-installed fastening system were analyzed, including the strength,reinforcement, thickness and cracks of the base material, anchoring depth, edge distanceand spacing, stiffness of fixture and so on.(2) The calculation method of tensile bearing capacity in different failure modeswere summarized, which were compared with the specifications at home and abroad, andcompared Fischer with HILTI product standards.(3)Test system of bonded metal anchor group was designed and two group of singleanchor, double anchors, four anchors and six anchors were tested. The failure mode,tensile bearing capacity and displacement of anchors were obtained.(4)The test results were analyzed and found that with the increasing of thickness ofthe base material, stiffness of fixture, quality of anchors and edge distance, the tensilebearing capacity of single anchor on average and the displacement of anchors wereincreased as well, and characteristic of ductile damage was more visible. Furthermore, theuneven coefficient of anchor force and the improvement coefficient of anchor force causedby stiffness of fixture were obtained. (5)With the help of ANSYS software, anchor group was numerical simulated. Theresult of numerical simulation was anatomized well with the results of tests.

Related Dissertations

  1. Study on the Mechanical Properties of Pva-high Toughness Cementitious Composites,TU528
  2. Analysis on the Failure Mechanism of Composite Ground under Flexible Foundation,TU473.1
  3. Experimental Study on Material Properties and Double-Layer Cushion of ETFE Foil,TU38
  4. Study on Contact Fatigue Performance and Fatigue Damage Mechanism of Coatings Prepared by Supersonic Plasma Spraying,TG174.44
  5. The Seismic Capacity Evaluation of Long-Span Concrete Filled Steel Tubular Arch Bridges,U442.55
  6. Effect of Heat Treatment on Microstructure and Mechanical Properties of Low Activation Ferrite/ Martensitic Steels Used for the Fusion Reactor,TG161
  7. Study on Mechanic Behaviour and Failure Mode of Circular Foundation in Rock Subgrade,TU476
  8. Test Study and Finite Element Analysis of the Work Mechanism of the Rock Anti-Float Anchor,TU472
  9. Testing Study on Seismic Characteristics of Wrap-Styled Reinforced Earth Retaining Wall,TU476.4
  10. Experimental Study on the Mechanical Behaviors of Screw Pile under Inclined Load,TU473.1
  11. The Engineering Characteristic of Phosphogypsum and Its Slope Stability Analysis,TU43
  12. Dynamic Responses and Failure Modes Analysis of Single-Layer Reticulated Domes under Impact Loads,TU399
  13. Failure Modes of Geodesic and Schwedler Reticulated Domes Under Impact Loads,TU399
  14. Key Technologies of Dam-break Life Loss Risk Assessment Research,TV122.4
  15. Dynamic Constitutive Relationship of TC4 Titanium Alloy,V250.2
  16. Study on the Failure Mechanism and Stability of Soil Slope,P642.22
  17. Key Technology Research on Performance-based Seismic Design of RC Shear Wall,TU375
  18. Experiment Research on Rupture Mechanism of Loess by Triaxial Tension Test,TU444
  19. Experimental Study on the “Y”–type Tubular Joints with Cross-weld,TU392.3
  20. Disc bolt destruction mechanism and application of technology,TU472
  21. Three-dimensional Slope Stability and Failute Analysis Using Shear Strength Reduction Finite Element Method (SSR-FEM),TU43

CLC: > Industrial Technology > Building Science > Building structure > Concrete structure,reinforced concrete structure
© 2012 www.DissertationTopic.Net  Mobile