Dissertation > Excellent graduate degree dissertation topics show

Dynamic Response of High Speed Flexible Rotor Due to Sudden Large Unbalance

Author: YeDong
Tutor: XuanHaiJun
School: Zhejiang University
Course: Chemical Process Equipment
Keywords: High-speed flexible rotor Blade out Sudden unbalance Limit bearing load Overall vibration response tester
CLC: TH133
Type: Master's thesis
Year: 2014
Downloads: 0
Quote: 1
Read: Download Dissertation

Abstract


The structure vibration response of the rotor and the installation section caused by sudden unbalance load due to blade out of the high-speed flexible rotor has been the focus in the field of aviation engine development. This paper is mainly about the sudden unbalance response characteristics of the rotor due to blade out of the high-speed flexible rotor. To this end, the main researches are as follows:(1) A simplified rotor-bearing system is modeled use LS-DYNA to carry out the blade out simulation analysis. Further simulation is analyzed with different blade out mass and blade out velocities. Unbalance response of the rotor and the load ability of the support bearing are analyzed in detail under various weights and blade out speeds condition. Failure mode of the rotor shaft is twist. Rub between the rotor and the limit bearing is classified as follow two states:one is the discontinuous interaction that causes twist of the rotor. The deformation can restore to equilibrium state after the rub to decrease unbalance response. Another one is the continuous interaction that the rotor doesn’t restore back and the shaft break at the weakest region. The two conditions occur in sequence. Studies have shown that with the increase of the distance from the axis point to the limit support, the protective effect of the limit support is more weak. Three different gap values are compared to study the vibration response. With the increase of the gap value, the load between rotor and limit support firstly increase and then decrease. However, The protective effect may decrease with large gap value. It is concluded that load is not the only factor related to failure. Axial displacement of the rotor should also be considered.(2) Dynamic response of high speed flexible rotor due to sudden large unbalance is studied with the use of high speed rotational tester,ZUST6D. Blade out tests of various weights and various speeds are carried out. It is found that the amplitude of sudden rotor vibration and the load on limit support is in the same magnitude due to either single blade out or full blade out. However, more danger is brought to high speed flexible rotor due to single blade out. Large unbalance on long duration on limit support-support base-protection ring-hanger make the system vibrate severely. This response can lead to failure of the installation section on real engine. The higher rotor speed and unbalance mass can lead to more severe vibration response. (3) Horizontal high speed rotation tester is built mainly with the turbocharger for overall vibration response research due to fan blade out. Initial set-up and power-on test is completed and improvement suggestions are made.

Related Dissertations

  1. Numerical Study of the Effect with Straight and Bowed Stator in Different Axial Gaps,TH45
  2. Axial fan blade vibration non-contact measurement,TD441.2
  3. Study on the Computer Aided Design of Die Forging Blade and Devices,V263.1
  4. Vertical-axis Magnetic Levitation Wind Turbine Bearing and Blades,TM315
  5. Research and Development of UG-based Four-axis CNC Machining Module for Turbine Blade,TK263.3
  6. Numerical Analysis of the Flow in Low-Spped Axial Compressors with Circumferentially Skewed Blades Using a Streamline Curvature Approach,V232.4
  7. Research of Rotor Dynamics Characteristics under the Action of Air Force,TH113
  8. Design and Characteristic Analysis on Blades of Horizontal Axis Marine Current Turbine’s Mechanics,TM312
  9. Boron carbide sintered diamond saw blades in the Applied Research,O474
  10. The Research of the Development of Blade Forging’s Profile Inspection System,TG316.193
  11. The Research of Computer Aided Fixture Design for Turbine Blade,TP391.72
  12. Optimization Design and Characteristic Analysis of Wind Turbine Blade using NPU new Airfoil,TK83
  13. Study on Fan Blade & Curving Mould Based on UG NX Software,TG76
  14. For stainless steel semi-finishing , finishing positive insert geometry,TG711
  15. Research and Application of Energy-capturing Area of Flexible Blade Turbine,TM315
  16. Study on Structural Dynamic of Large Turbine Blade of SMA Composite,TK83
  17. Fatigue Life Evaluation of Flue Gas Turbine Blades,TK263.3
  18. Study on the Adaptive Blade Pitch Control of Electrically Controlled Rotor,V225
  19. The Parameter Vibration of Shroud Blade,O323
  20. Research on Tool Path Generation Technology in the Multi-axis Belt Grinding for Blade,TG580.6
  21. An Experimental Study of DLC Film on Razor Blade Edge,TG174.4

CLC: > Industrial Technology > Machinery and Instrument Industry > Mechanical parts and gear > Moving parts
© 2012 www.DissertationTopic.Net  Mobile