Dissertation > Excellent graduate degree dissertation topics show

Study on Improvement of Specific Capacity and Rate Performance of Li-MnO2Battery

Author: YuLiQiu
Tutor: CaoDianXue
School: Harbin Engineering University
Course: Applied Chemistry
Keywords: Electrolytic manganese dioxide High energy ball-milling Heat treatment Positive electrode preparation
CLC: TM912
Type: Master's thesis
Year: 2013
Downloads: 51
Quote: 0
Read: Download Dissertation

Abstract


Li-MnO2primary battery demonstrates high specific capacity and high specific power.It has been widely used in military and daily life such as portable electronic devices.However, there is a severe capacity loss when Li-MnO2battery is used at high dischargerate. The high rate performance of the battery is limited by the positive electrode material ofelectrolytic manganese dioxide（EMD）. In this thesis, the effect of high energy ball-millingtreatment of EMD on its morphology, structure and discharge performance are stuided,aiming to improve the discharge specific capacity and high rate discharge performance ofEMD in Li-MnO2battery.The influence of high energy ball-milling treatment on the structure and dischargeperformance of EMD is first investigated. SEM and TEM results show that the morphologyof EMD was obviously changed from irregular block to spherical particles with a significantdecrease in particle size fater ball-milling. The majoty of the particle have nanosizeddimesion and the largest particles have a diameter of less than around5m. The result ofXRD showed that the ball-milling did not alter the crystal structure of EMD, which has aγ-phase and γ/β mixed phase after heated at400℃for12h. The electrochemical testdemonstrated that the ball-milled EMD has better electrochemical performance thancommercial EMD. At the discharge rate of0.1C, the specific capacity of the ball-milledEMD is26%higher than that of the prinstin commercial EMD.The effects of thermal treatment temperature and quenching on the dischargeperformance of ball-milled EMD were stidued. The result of XRD indicated that MnO2wasconverted from γ-MnO2to β-MnO2upon heating treatment, and only presents as β-MnO2when the temperature reached450℃. The sample heated at400℃showed the bestdischarge performance. At the discharge rate of0.1C, the specific capacity of the EMD was242mAh·g-1. Quenching treatment did not change the structure of EMD but make the edgeof particles smoother. The discharge platform voltage of the quenched EMD was higher thanthat of the unquenched EMD.The EMD electrode made by mechancial pulping was better than that made byball-milling pulping. At the discharge rate of0.1C,0.5C and1C, the specific capacity ofthe electrode using PVDF as binder was17%,19%and19%higher than that using LA-132 binder, respectively. The specific capacity of the electrode made by adding CFxin the EMDwas286,169and163mAh·g-1at the discharge rate of0.1C,0.5C and1C respectively,which proved that the discharge performance of the electrode was improved obviously byadding CFx.

Related Dissertations

  1. Study on Key Technology and Its Physiological Basis of Virus Elimination and Rapid Propagation of Phalaenopsis,S682.31
  2. Study on the Subsurface Crack of Supporting Roller Made of Austempered Ductile Iron,TG156.3
  3. Thermophysics Research on Postharvest Spherical Fruit during Heat Treatment,S66
  4. Research on the Microstructures and Properties of Semi-solid ZL201 Alloy Die Forging,TG146.21
  5. The Research on Rolling and Heat Treatment Technology of AZ31 Magnesium Alloy Thin Sheet,TG166.4
  6. Effect of Heat Treatment and Alloy Composition on Microstructure and Properties of Wear-resistant Casting Steel,TG142.4
  7. Research on Composite Hard Anodic Oxidation of Aluminum Alloys and Mechanism,TG174.44
  8. Effect of Ag and Er on Microstructures and Properties of Al-Mg-Si-Cu Alloys,TG146.21
  9. Study on Extrusion and Heat Treatments of AJ and AE Series Cast Magnesium Alloys,TG166.4
  10. Study on Blast Furnace Slag cementitious material produced by Electrolytic Manganese Dioxide Slag-alkali complex activated,X78
  11. The Design and Implementation of Control System for Wire-steel Heat Treatment Direct-fired Furnace,TP273
  12. Study on Process Method and Parameter Optimization of the Remained-heat Treatment of Marine Heavy Forgings,TG316
  13. Study Continuous Glass Fiber Reinforced Polypropylene by Two-step Pultrusion,TQ327.11
  14. Study on the Preparation and Thermostability for Mechanical Properties Microstructure of Low Density MA/ ODS Nickel-Based Superalloy,TG132.32
  15. Study on the Preparation Technology, Structure and Properties of Carbon Fiber from Cnts Reinforced Lyocell Fiber,TQ342.742
  16. Studies on the Structure and Hydrogen Storage Properties of La-Mg-Ni System AB3.0-3.5 Type Alloys,TG139.7
  17. Research on Pricipitated Phrases and Corrosion Resistance of INCOLOY 028,TE980
  18. Reseach on Wear Resistance and Contact Fatigue Performance of Alloy Cast Steel for Roller,TG333.17
  19. Study on Microstructure Stability and Dynamic Recrystallization of GH80A Alloy Used for Steam Turbine,TG132.32
  20. Study on RT-PCR Detection and Elimination Technique of Citrus Tatter Leaf Disease,S436.66
  21. Study on Synthesis and Modified of LiFePO4 as Cathode Materials,TM912

CLC: > Industrial Technology > Electrotechnical > Independent power supply technology (direct power) > Battery
© 2012 www.DissertationTopic.Net  Mobile