Dissertation > Excellent graduate degree dissertation topics show

Study on the Influence of Hot Deformation and Quenching-tempering Process on the Microstructure and Mechanical Properties of Oil Storage Tank Steels

Author: DuanZhengTao
Tutor: ZhuFuXian
School: Northeastern University
Course: Materials Processing Engineering
Keywords: oil storage tank steel thermal simulation hot deformation quenching and tempering direct quenching
CLC: TG161
Type: Master's thesis
Year: 2009
Downloads: 38
Quote: 0
Read: Download Dissertation

Abstract


The building of strategic oil reserves is very important to the national economic security. The construction of large floating roof oil storage tanks with volume more than 100,000 m3 requires steels with high strength, good toughness and favorable welding properties. However, more than 90% high-strength oil storage tank steels depend on imports; it’s expensive and can not ensure date of delivery. For profit of business and our country, the National Development and Reform Commission urges to manufacture domestic oil storage tank steels in China, on one hand to meet the needs of the domestic market, build strategic oil reserve for the country’s security; On the other hand, to improve domestic production technologies and theories of the heavy plate and elevate the technical level of enterprises. Considering the welding process of large-scale tank’s, when the plate thickness is 21mm was used V-groove and Gas-electric welding, and the input energy is 90～100kJ/cm. Therefore many technologies of large-scale input energy storage tank steels needed to research and developed. In this paper, combine Northeastern University with 4300mm heavy plate R&D center of ShouQin Metal Materials Co.,Ltd, to research oil storage tank steel plate, and systematic study on thermal deformation of tested steel. The main thesis is as follows:(1) Using thermal simulation experiment to determine the critical temperatures of tested steel; drawing static and dynamic CCT curves and researching the cooling rate, holding temperature and deformation on the impact of continuous cooling transformation. The results showed that the beginning transformation temperatures decrease with the increasing of cooling rates; deformation increases the beginning transformation temperatures.(2) Studying on the relationship between total reduction in non-recrystallization zone and mechanical properties and microstructure of tested steels. The results showed that the tested steel with total reduction about 60% in non-crystallization zone has the best mechanical properties.(3) Studying on the influence of reheat quenching or direct quenching on mechanical properties and microstructure of tested steel; It showed that the steels with tow processes:the offline quenching and tempering(950℃+40min,650℃+50min) and online quenching, offline tempering(835℃,650℃+50min), have similar mechanical properties.(4) The different online quenching temperatures on the influence of microstructure and mechanical properties of tested steel have been studied. The results show that with the quenching temperatures at 910℃,880℃and 850℃, the mechanical properties of steel remains basically unchanged, the most appropriate quenching temperatures of tested steel is between 850℃and910℃.(5) Carrying out industrial trial of SG610D steel, studying on the microstructure and mechanical properties of the steels with rolled state and quenched and tempered state. Comparing with rolled state, the mechanical properties of tested steel with quenched and tempered has greatly improved; Comparative experiment showed that the mechanical properties of SG610D steel with quenched and tempered achieve the requirement of similar products of Japan. SG610D steel can be used for domestic construction of large oil storage tank.

Related Dissertations

  1. Research on Low-temperature Pressure Vessel Steel 07MnNiMoVDR Rolled and Quenched and Tempered Technology,TG156.6
  2. The Effect of the Hot Deformation Behavior on 20 and 10B21 Steel Austenite Grain Morphology,TG331
  3. Effect of Thermal Deformation on the Structure and Magnetic Properties of Ni45Co5Mn36.7In13.3,TG139.6
  4. The Study on Re-dissolution and Precipitation Behavior of Second-Phase Particles in High Strength Hot-rolled Dual-phase Steel,TG335.11
  5. Experimental Cold Study and Simulation Research of High Temperature Burner for Low Calorific Value Gas,TK223.23
  6. Martensitic Transformation Crystallography and Finite Element Simulation of Microstructure in Steels,TG142.24
  7. Cast aluminum matrix composite behavior of hot extrusion,TB331
  8. Shortwave four power combiner design and simulation studies,TN73
  9. GH625 alloy hot deformation behavior and dynamic recrystallization of,TG132.32
  10. Investigation of the Stress-Strain Behavior of Hot-compression Mg-Li Alloy,TG146.22
  11. The Research on the Non-equilibrium Microstructure of Ti6Al4V Alloy,TG146.23
  12. VN micro -alloying 77B, 82B steel microstructure and properties of,TG142.1
  13. Micro Ti pipeline weld heat affected zone properties,TG401
  14. Thermal Simulation and Thermal Properties of Epoxy Packaging Materials,TQ323.5
  15. Research on Double-wire Saw Technology and Microstructure Behavior of the Welded Joint of 10Ni3CrMoV Steel,TG445
  16. Research on Evolution of Microstructure in Low Carbon Steels for Fasteners,TG142.11
  17. Study on Rolling and Heat Treatment Processing of Low-carbon and Low-alloy Plastic Mould Steel,TG161
  18. Study on the Processing Property of Domestic Petroleum Storage Tank Steel Plate,TE972.1
  19. Effect of Heat Treatment on the Microstructure and Mechanical Properties of Two Quenching and Tempering High Strength and Low Alloying Steels,TG161
  20. Study on Interruption Turning Technique of CNC Turning Machine,TG519.1

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > Heat treatment > Heat treatment of steel
© 2012 www.DissertationTopic.Net  Mobile