Dissertation > Excellent graduate degree dissertation topics show

Preparation and Packaging Performance of Chip on Board Ceramic Substrate for High-power LED

Author: FangJun
Tutor: FuRenLi
School: Nanjing University of Aeronautics and Astronautics
Course: Materials Science
Keywords: High-Power LED Thick Film Process COB (Chip On Board) Package CeramicSubstrate Package Structure Thermal Resistance
CLC: TN312.8
Type: Master's thesis
Year: 2013
Downloads: 23
Quote: 0
Read: Download Dissertation

Abstract


In this paper, on the basis of COB package structure and substrate for the high-power LED, thethick film process which without a glass phase Cu slurry system of reactive bonded method was used.The metallization of ceramic substrate was realized though sintering and reduction heat treatment, andthe densification process was also tried. On the basis of thick film technique, the screen was designedby the existing LED substrate graphic, and prepared by screen printing process. The electroplatingfixture was designed to dense the circuit graphics which was prepared by thick film technique.Then,the high performance ceramic substrate for COB package was prepared. The package structure wasimproved which use solder replace the thermal plastic, and then self-made COB ceramic substratewas packaged. The phase composition and morphology of samples were analysised by X-raydiffraction (XRD) and scanning electron microscopy (SEM).The mechanical and electrical propertieswere tested and analysised, and the optimization of substrate preparation process was made. ANSYSthermal simulation was used to forecast heat dissipation performance of the improved packagestructure. The thermal performance of the COB ceramic substrate using new structure was also testedand evaluated.The results show:1) The Cu slurry had good rheological properties, which viscosity can becontrolled at100~300Pa·s, and the thickness was also controlled according viscosity regulation.2)The thick film Cu layer can be prepared upon sintering and reduction heat treatment.The optimumsubstrate surface was obtained by sintering at1050℃and reducting heat treatment at900℃. Thequality of surface Cu layer was further improved by bright plating copper process.3) After design andscreen printing circuit graphics, the best COB ceramic substrate was obtained under the conditionsthat the mass of coated slurry was0.08g, sintering temperature was1050℃, reducting temperaturewas900℃, which bonding strength was94N, and the surface sheet resistance was2.78m/□.4) Thesurface sheet resistance of COB substrate can further reduce that use the bright plating copper processbase on the designed electroplating fixture.When the current is0.3A, it only was0.9m/□.5)According to simulation analysis, the improved package structure can enhance the heat dissipation ofthe substrate. Thermal resistance fell to28.33K/W from50.69K/W.6) The package of COB ceramicsubstrate use welding method, its interface was dense without hole defects. The peel strength was8.66N/cm, and wasn’t failed after500thermal shock. The COB substrate with improved package wasapplied to LED systems, it was found that thermal resistance was only33.5K/W. The trend was consistent with simulation results.

Related Dissertations

  1. The Performance Experiments and Research of LPEC Plate Air Preheater,TQ051.5
  2. Research on North Wall Thermal-release Controling Based on Tempetature Modelling in Solar Greenhouse,S625
  3. Different refrigerant in the spiral groove petal-shaped fin tube condensation heat transfer enhancement research,TQ051.5
  4. Research of the Low Frequency Electrodeless Fluorescent Lamp System,TM46
  5. Design of DC 12V 30W High-power LED Drive Array with High-efficiency and Single Dimmer,TM923.34
  6. Research of In-situ Measurement of Ground Thermal Properties,P314
  7. Study on Thermal Resistance of PUE,TQ334.1
  8. Investigation of Condensation of Low-Pressure Vapor in a Horizontal Tube,TQ025
  9. Crystallization Property, Thermal Resistance, Thermal and Thermal Oxidative Stabilities of LLDPE Filled with Nano-SiO2,TQ325.1
  10. Research on Thermal Techniques of Solid State Modules,TN957
  11. Study on 1450nm High Power Semiconductor Laser Array,TN248.4
  12. Synthesis, Morphology and Properties of Polyurethane-Imides,TQ323.8
  13. Research on Heat Reflectionand Thermalresisitance Technology of Asphlat Pavement Cooling Mechanism and Its Application,U416.217
  14. The Study on Treatment of Acute Intracerebral Hemorrhage and Brain Edema with Cooling Blood and Clearing Stasis Therapy,R277.7
  15. Numerical Study on Heat Conduction Effect in Mini Crossflow Heat Exchanger,TQ051.5
  16. Preparation of High-power LED Aluminum Ceramic Heat Dissipation Substrate,TQ174.756
  17. Synthesis of Thermal Resistance of PUE and Study on Its Structure and Properties,TQ334.1
  18. Synthesis of Microcellular Polyurethane and Study on Its Properties,TQ334.1
  19. Synthesis of Thermal Resistance of Pue and Study on Its Structure and Properties,TQ334.1
  20. Study on Formation and Properties of Down Web Based on the Colligation of Warp Knitting,TB34
  21. Exhaust Valve Heating Boundary Heat Transmission Model and Thermal Load Estimate,U464.134.3

CLC: > Industrial Technology > Radio electronics, telecommunications technology > Semiconductor technology > Semiconductor diode > Diodes: structure and performance > Light-emitting diodes
© 2012 www.DissertationTopic.Net  Mobile