Dissertation > Excellent graduate degree dissertation topics show

Design of White Light LED Driver IC Based on Charge Pump

Author: LiYanZhao
Tutor: WenHuanMing
School: Hebei University of Science and Technology
Course: Circuits and Systems
Keywords: Charge pump Bias source Band-gap reference voltage source Error Amplifier Layout design
CLC: TN312.8
Type: Master's thesis
Year: 2009
Downloads: 72
Quote: 0
Read: Download Dissertation

Abstract


White LED driver chips play an important role in protect white LED devices to work stability,with the extensive use of white LED devices,white LED driver chips will have broad prospect for development. Current white LED driver chips rely mainly on imports, so design and development with independent intellectual property rights of white LED driver IC has important practical significance.This topic has designed a charge pump-based white LED driver chips,using CSMC 0.6μm standard process to complete the whole circuit layout and generate a GDSII file for process manufacturers to tape. The core circuit module of the driver chip includes charge pump circuit module , multi-voltage bias circuit,reference source,error amplifier,under-voltage protection and over temperature protection module.Charge pump circuit module is the key to the design of white LED driver chip.In this paper,based on the technology of 1 or 1.5 times self-adaptive charge pump boost,using special substrate connection,which enables the design parameters and performance of chip has been greatly improved.The simulation results shows that the charge pump output ripple less than 10mV,with a greater stability than existing white LED driver chips.The reference voltage value generated by reference source also has a very strong stability, from -55℃to 125℃,the output voltage variation is±1.5mV, temperature coefficient is 6.87 ppm/℃. The turn-off threshold voltage of under-voltage protection module is 2.35V, which can turn off the chip in a low voltage to prevent over-discharge power,in order to protect the power supply.Because there is large size chip switching devices,set the over-temperature protection module thermal shutdown threshold voltage at 150℃,it can turn off the ship when the temperature is too high.The chip design uses adaptive charge pump structure with Special substrate Connection,makes boost conversion to input voltage.Through adaptive adjustment to ensure six parallel white LED device input current constant,so that each LED device keeps the same brightness.The chip is mainly used in portable electronic products,the input voltage range is 2.7~4.5V.The chip’s operating frequency is 1MHz,the working temperature range is -40 ~ +85℃.Shutdown current can be as low as 1μA under chips completely shut-down mode.The entire circuit diagram and chip layout are completed in CADENCE which is widely used in the industrial sector,and each sub-modules and overall layout of the circuit are optimized. Through the design rule checking (DRC),schematics and layout horses right (LVS) verification and other verification tools to ensure the accuracy and reliability of the layout.

Related Dissertations

  1. Study on RFID Techniques in the Manufacture of Used in Automobile Ignition Coils,TP391.44
  2. Design of a 2.5GHz PLL Clock Generator,TN911.8
  3. The High Voltage Generation System Design in Nano-Crystal Memory,TN47
  4. A Low Power Power Management System for Passive RFID Tag Chip,TN402
  5. A low jitter CMOS PLL design,TN911.8
  6. Fractional-N frequency synthesizer Modeling and Design,TN74
  7. Applied to the gain cell embedded dynamic random access memory adaptive dynamic refresh and write voltage adjustment programs,TP333
  8. New embedded memory module study,TP333
  9. Low-cost , low power , highly integrated single-chip power system design,TP303.3
  10. Fractional Frequency Synthesizer Design,TN74
  11. The Design of 1.8GHz CMOS Integer-N Frequency Synthesizer,TN74
  12. Ism the Programming Design of the Ecosystem Agriculture Traveling Country Club,F327;F205
  13. Visual Communication of Information Research in Web Design,TP393.092
  14. Research on ΔΣ Fractional-N Frequency Synthesizer in 0.18 μm RF CMOS Technology,TN74
  15. Optimization and Design of High-efficiency Charge Pump for Security SRAM,TN432
  16. A reference voltage source , and the design of the linear regulator,TM44
  17. Modeling and Simulation of Mixed-signal Systems Based on Verilog-AMS,TN911.7
  18. Litho Defects Research in ASIC Layout Design,TN492
  19. The charge pump Buck switching power supply chip design,TN86
  20. CMOS Rail-to-Rail operational amplifier chip design,TN432
  21. The Application of the Particle Swarm Optimization on the Engine Room Arrangement,U662

CLC: > Industrial Technology > Radio electronics, telecommunications technology > Semiconductor technology > Semiconductor diode > Diodes: structure and performance > Light-emitting diodes
© 2012 www.DissertationTopic.Net  Mobile