Dissertation > Excellent graduate degree dissertation topics show

Research on High Speed Automatic Sorting Technology for the Diameter of Bearing Needie Roller

Author: LiBaoCai
Tutor: ChenZuoXue；YangShuNian
School: Huazhong University of Science and Technology
Course:
Keywords: the Diameter of the Bearing Needle Roller Automatic Measurement Sorting technology Virtual Instrument Servo System
CLC: TH133.33
Type: Master's thesis
Year: 2011
Downloads: 60
Quote: 0
Read: Download Dissertation

Abstract


Rolling bearings are widely used in electromechanical equipments. Their performance isvital important to the equipments. Measuring and sorting needle rollers are the most importantprocesses for the assembly of rolling needle bearings. The accuracy of measuring and sortingwould influence the bearings’ performance after assembled. In this paper，a method to sort thediameter of the bearing needle rollers in high precision and high speed is researched.For high-speed sorting of the diameter of the needle rollers, the rapid feeding and sortingmethod is chosen. At the same time, the way for signal acquisition and the way to drive thesystem have been optimized. So the time cost for the needle roller feeding, transportion,sorting and its diameter measuring has been shortened dramatically. The system designed inthis paper is composed of two parts: the mechanical part and, the measurement and controlpart.The mechanical part mainly includes the needle roller transportion mechanism, themeasurement mechanism and sorting mechanism. The needle rollers are transported by thetransportion mechanism driven by the servomotor in high speed in the way of intermittentrotation. Measure mechanism is used to fix the transducer and make fine adjustment. Theparallel spring is used to ensure the high precision. Needle roller sorting mechanism is drivenby rotary electromagnet and used to carry out the blanking and sorting of needle rollers inhigh speed .The design of the measurement and control part is based on Labview virtual instrumentplatform. We design the hardware and interface and write the measurement and controlprogram. The control of servomotor is implemented by motion-controlling card andservo-amplifier. Collection and transformation of the signal of the diameter of the needleroller is completed by the inductance sensor, inductance micrometer and the data acquisitioncard. And industrial computer is applied to control the actions of the system, to process thesignals and to make group judgement.According to the implementation scheme, a prototype has been developed. And itsmeasuring accuracy and sorting efficiency have been tested. The results show that theprototype could sort the needle rollers in the speed of 350 pieces per minute, and its repeataccuracy is±0.9μm. The main errors of the system were also analysed.

Related Dissertations

  1. Study of Automobile Ignition Coil Testing System Based on Standard LAH032.905,U472.9
  2. Design of Weapon Detection Device Control System,TP183
  3. Development of Tractor’s Virtual Instrument System Based on CAN Bus,S219.02
  4. LabVIEW-based virtual oscilloscope design and remote control,TM935.3
  5. CAN bus technology in the meteorological monitoring System Research and Implementation,P409
  6. Design of Analysis System of Audio Signals Based on Virtual Instrument,TP274
  7. Surface Plasmon Resonance Instrument Software Development Model Based on Data Flow Architecture,TP311.52
  8. The Research and Design of Software of Virtual Digital Oscilloscope,TP311.52
  9. Research and Application of Remote Virtual Instrument Experimental Teaching System Based on LabVIEW,TP391.6
  10. The Design and Exploitation of Furnace Temperature Measurement and Control System Based on LabVIEW,TP274
  11. Research on Thin-Film Hysteresis Loop Measurement System Based on Extraordinary Hall Effect,O484.43
  12. Research on Automatic Measurement Technology of Pitch Diameter for the Rzeppa Joint Housing Raceways,TG80
  13. Development and Experimental Study about Virtual Instruments of Vibration Test and Analysis System and Combustion Analyzer,TK407
  14. Testing Systerm of Pump,TD442.2
  15. CNC machine remote monitoring technology research,TG659
  16. Research and Development of Electrohydraulic Proportional Test Bed for Width Adjustment Cylinder of Continuous Casting Mould Based on Virtual Instrument,TF341.6
  17. Research on Parmeters Estimation of Digital Moudulation Signals,TN911.3
  18. The Design of Virtual Simulation Platform Based on LabVIEW,TP391.9
  19. Research on Wireless AE System Based on Wireless Sensor and Virtual Instrument Technology,TP212
  20. Research on Excitation Signal and Frequency Domain Identification of the Servo Control System,TP273
  21. Time and space -related imaging technique (STIC) of fetal ventricular volume and function,R714.5

CLC: > Industrial Technology > Machinery and Instrument Industry > Mechanical parts and gear > Moving parts > Bearing > Rolling
© 2012 www.DissertationTopic.Net  Mobile