Dissertation > Excellent graduate degree dissertation topics show

Research on Static Magnetic Field and Torque Characteristics of Hybrid Stepper Motor Based on ANSYS

Author: WangHuan
Tutor: LiXingGen
School: Zhejiang University
Course: Motor and electrical
Keywords: ANSYS Finite Element Method Torque characteristics Enhanced hybrid stepper motor
CLC: TM383.6
Type: Master's thesis
Year: 2012
Downloads: 190
Quote: 1
Read: Download Dissertation

Abstract


Due to the limitation of computing performance of the computer,2D FEM (Finite Element Method) was always used for the electromagnetic field analysis of the hybrid stepper motor in the past, such as tooth-layer specific permeability method. However, the electromagnetic field of hybrid stepper motor is a typical highly saturated 3D nonlinear electromagnetic field. The magnetic field distribution is very complicated; especially the axial magnetic distribution is not uniform because of the influence of axial magnetizing permanent-magnetic materials installed on the rotor. With the development of computer performance and the application of the universal finite element software,3D finite element analysis of the whole motor magnetic field is practical and feasible. Therefore,3D finite element model of the hybrid stepper motor was set up to analyze static magnetic field and calculate the torque characteristics in this dissertation.Firstly,3D finite element model of two-phase and five-phase hybrid stepper motor is established by the universal finite element analysis software ANSYS, based on the basic of the electromagnetic field theory, to calculate the static magnetic field distribution. Static characteristics, especially the torque-angle characteristics which is very important to the performance of the motor, is further calculated.Then, the torque-angle characteristic calculation program is written, based on the traditional tooth-layer specific permeability method, to calculate the torque characteristics of the above two-phase and five-phase hybrid stepper motor. Then, the calculation results are compared with ANSYS calculation results and the experimental results. The study found that, the calculation precision of ANSYS calculation method is obviously improved.An enhanced two-phase hybrid stepper motor which has permanent-magnetic materials installed in the stator slots is introduced in this dissertation.3D finite element model of the motor is established by ANSYS to calculate the torque-angle characteristics, and then compared with the same type standard two-phase hybrid stepper motor. The study found that, the static torque of Enhanced hybrid stepper motor is greatly increased. And the torque production mechanisms are further analyzed. Optimization design of enhanced hybrid stepper motor tooth layer structure, air gap and properties of the stator slot permanent-magnetic materials are carried out, based on the target of maximum static torque output and improve torque-angle characteristics curve waveform.

Related Dissertations

  1. Research on the Structure and Characteristics of Permanent Magnetic Coupling,TH139
  2. Simulation Analysis on Temperature Stress of RCC Arch Dam and Its Construction Joints Design Research,TV642.2
  3. Analysis and Study of Abutment Stability in Concrete High Arch Dam by Three-Dimensional Nonlinear Finite Element Method,TV642.4
  4. The Effect of Current Density and Electric Field on Ni and Its Alloy Electrodeposition for Copper Crystallizer,TQ153.2
  5. Stability Analysis of Roller Compacted Concrete Gravity Dam Based on Time-history Method,TV642.2
  6. Broken walnut shell force testing and virtual prototype design of the main components of walnut sheller,S226.4
  7. Research on a Fire-fighting Shell for Towers,TU892
  8. Research on Intelligent Aerial Bomb for Forest Fire Fighting,S762
  9. Bearing Capacity of Cast-in-place Piles in the Karst Region of Yichun, Jiangxi,U213.1
  10. Analysis of Seismic Behaviour of Mega Frame-Tube Structure Based on ANSYS,TU352.11
  11. Parametric Finite Element Analysis System Development of the Jib of Tower Crane Based on ANSYS,TH213.3
  12. Design and Study of a New Wind Generator,TM315
  13. Research of Deep Excavation Construction Process for Nearby Subway Section Action,TU753
  14. FEA of the Small Multi-function Chassis Frame and Its Lightweight Design,S223.91
  15. Application of Vector form Intrinsic Finite Element Method in the Analysis of Cable Membrane Structures,TU399
  16. Tower-belt Structural and Dynamic Characteristics Simulation Analysis,TH213.3
  17. Optimum Design and Study of Large-cantilever Steel Tube Truss Structure,TU392.3
  18. Reserch on the Simulation and Optimization of Self-Piercing Riveting Process for Dissimilar Materials,U466
  19. The Research on Stability and Dynamics of Cylinders in Axial Flow,O353
  20. Stress Distribution in Iron Boron Matrix Composites Reinforced by Fiber,TB332
  21. Research on the Behavior of Rectangular Concrete Short Columns Confined with BFRP Sheets,TU377

CLC: > Industrial Technology > Electrotechnical > Motor > Micro-motor > Control of micro motor > Stepping decline of motor
© 2012 www.DissertationTopic.Net  Mobile