Dissertation > Excellent graduate degree dissertation topics show

The Optimal Technique of Extended Reach Well Profile

Author: LiangChengLiang
Tutor: LiZuoï¼›YangYuJing
School: Xi'an University of Petroleum
Course: Petroleum and Natural Gas
Keywords: Extended Reach Well Profile Optimal Technique
CLC: TE21
Type: Master's thesis
Year: 2010
Downloads: 67
Quote: 0
Read: Download Dissertation

Abstract


The one of the difficult problem of the Extended Reach Drilling Technology is to design the optimal profile. To carry out the Extended Reach Well profile optimization design method, the non-linear mathematical programming theory was introduced to the design to the optimal profile of Extended Reach Well. Put forward a well bore length of the shortest objective function, optimal design of large displacement cross-section wells mathematical method; the use of the method were established by circular curves, catenary, lateral catenary, the amendment catenary, lateral orbital amendment catenary Optimization design model. According to the most brachistochrone principle, proposed a new track section--cycloidal orbit, and gives the optimization model and design methods. Comparative analysis shows that when the horizontal displacement is large, cycloid orbit with a shorter casing length, friction, and friction characteristics of a small twist. According to different tracks within a borehole drill string friction and the friction torsion calculation results and analysis show that the large displacement wells, and stabilize the slope segment accounts for the friction in the main part of the overall friction. When the bending Hole drill string pressure, the drill string and the borehole wall contact force increases, will result in a significant increase in the overall sliding friction. Therefore, from the perspective of reducing sliding friction to prevent the bending section of drill string pressure on the basis put forward the concept of the critical stability angle. When put forward the concept of critical angle for the large displacement cross-section design of wells to determine the key parameters of solid angle provides a theoretical basis and selection range. Proposed an integrated optimization design method of borehole length, the friction Moroccan twist angle stability analysis and critical concepts, this paper established a two-dimensional large displacement Well Trajectory optimization design methods and procedures. Using the method of extended reach wells profile design, with a track length of the short, twisting friction, friction is small, the advantages of simple design and calculation.

Related Dissertations

  1. Jack-up drilling platform hydrodynamic characteristics,TE21
  2. The Dynamics Analysis of Rod String in Screw Pump Well and Research Eccentric Wear Prevention Methods,TE21
  3. Analysis of Fluid Pressure and Velocity in Annulus of Foam Drilling,TE21
  4. The Analysis of Vibration Spectrum on Drill String of Extended Reach Well,TE21
  5. Drilling pressure measuring device key components Vibration Analysis and Research,TE21
  6. Simulation Analysis on Vibration of Vertical-oil-well Drill String Based on ANSYS,TE21
  7. Experimental Research on the Separation and Recycling Efficiency of Particles in Particle Impact Drilling System,TE21
  8. Based on logging data and support vector machine Drillability research,TE21
  9. The Jet Characteristics Theory Analysis and Numerical Simulation of Oil Well High Pressure Water Rock Breaking Nozzles,TE21
  10. A Study on Fatigue Reliability of Simplified Model Semi-submersible Drilling Platform,TE21
  11. Test wells column mechanical calculations,TE21
  12. Wells connected well section of wall mechanical stability,TE21
  13. The Simulation and Optimization of the Key Components of Retrievable Casing Drilling Tools,TE21
  14. Hydraulics Calculation and Suction Module Design for Riserless Mud Recovery Drilling System,TE21
  15. Mechanism Study on the Bottomhole Pressure Reduction by Drilling Fluid Shunt on Bit,TE21
  16. Research on Measurement and Analysis of Drillstring Vibration,TE21
  17. Numerical Simulation of Flow Characteristics of Non-newtonian Fluid in a Hydrocyclone,TE21
  18. The Study on Technology and Hydraulic Parameters in the Constant Bottom Hole Managed Pressure Drilling,TE21
  19. Research of Matrix Distributed Computing for Finite Element Analysis of Drill String Mechanics,TE21
  20. Study on Rock Breaking Rules of Particle Impact Drilling,TE21
  21. Study on Drilling Pipes and Annulus Flow Characteristics of Drilling Fluids with Particles,TE21
  22. Technology of Air Drilling and Its Application in the Northeast Area of Sichuan,TE21

CLC: > Industrial Technology > Oil and gas industry > Drilling engineering > Drilling theory
© 2012 www.DissertationTopic.Net  Mobile