Dissertation > Excellent graduate degree dissertation topics show

Research on Key Technique of Multi-unit Parallel Converter in Wind Power Generation System

Author: LvJing
Tutor: CaiXu
School: Shanghai Jiaotong University
Course: Power Electronics and Power Drives
Keywords: wind power generation converter multi-unit parallel circulating current feedforward compensation RT-LAB
CLC: TM46
Type: Master's thesis
Year: 2011
Downloads: 130
Quote: 0
Read: Download Dissertation

Abstract


As a result of increasing energy requirement and more concern of environment protection, the use of wind energy for electric power generation becomes a vital alternative to replace the conventional energy. The technologies on wind power generation become a research hotspot. Offshore wind power generation has becoming a more and more important research direction due to its characteristics. The converter is one of the core technologies in wind power system. With the increasing of the capacity of single wind turbine, how to realize high-power converter in the low-voltage conditions is an important problem demanding prompt solution. It is well know that multiphase converters can be paralleled to increase the power rating, reliability, efficiency, as well as decrease the cost and current/voltage ripples. In addition, the parallel structure is very suitable for modular system design and system reconfiguration, providing better flexibility. So the converter parallel technology has a wide range of applications in the high-power occasions.However, the circulating current will occur when the device parameters, switch states, control parameters and so on between paralleled converters are different. The circulating current will increase switch stress and compel the converters to run under reducing the operating power level. The circulating current will cause the over-current faults in serious cases. Thus, the control targets of parallel-converter is realizing the consistency in the frequency, amplitude and phase of output voltages of the parallel units and finally realizing the load-sharing between the parallel units. At present, the study of paralleled single-phase UPS is more, but the study of high-power three-phase wind power converters is less. So, the issues of this paper have important practical significance.First, an overview of domestic and international wind power development and trend is introduced in the paper. Then, several popular patterns of parallel converter are discussed. The control strategy of three-phase grid-connected converter is introduced. The general definition of circulating current is given in the paper and the concept of circulating current percentage is proposed to evaluate the amount of circulating current. And then the causes producing circulating current are analyzed based on the mathematical model of circulating current in parallel-converter system. The characteristics difference of circulating current between centralized control and distributed control mode is pointed out. For the distributed control structure, theoretical analysis and simulation results of the proposed zero-sequence circulating current control strategies are given in the paper. According to feedforward control theory, the circulating current control strategy based on circulating current feedforward compensation is proposed. The hardware circuits and control software are designed. The results of hardware in-the-loop simulation experiment are given based on RT-LAB. The experimental results show that the proposed circulating current control strategies are able to reduce the DC and low-frequency circulating current effectively.

Related Dissertations

  1. The Equivalent Circuit Model of Radial Vibration Mode Piezoelectric Transformer and Its Application,TM406
  2. Grid-Side Converter Control and Wind Turbine Emulator in Direct Drive Wind Power System,TM46
  3. Research on the Topologies of Polarity-Variable Micro Oxidation Pulse Power,TN86
  4. Research on Power Supply of Contactless Power Transfer System,TM46
  5. A Research on Erection Technology of 210 Tons Converter Ontology Equipment in New Steel Group,TF748.2
  6. Research on π Type AC/AC Converter with Variable Structure Control Strategy,TM46
  7. The Research of Wind Power Generation System Based on DFIG,TM614
  8. Microwave frequency with the LLC resonant soft-switching power,TM925.54
  9. Digital Delta Type UPS Design and Research,TN86
  10. Research on Control of Direct Driving Type WTG Grid Converter Based on DSP,TM46
  11. Design and Implementation of the CAN-Ethernet communication protocol converter based on ARM9,TP273.5
  12. The Research and Design of Converter Steelmaking Endpoint Guiding System,TF345
  13. The Feasibility Study on Oxygen Converter Gas Purification and Recycles of SGBY Ltd,F426.31
  14. Dynamic Routing and Wavelength Assignment Algorithm of WDM Optical Networks,TN929.1
  15. Research on Matrix Converter Fed Induction Motor Vector Control System,TM346
  16. Research of IF Sampling Receiver Technology,TN858
  17. Research and Development of Embedded and Precision Network Time Server Based on Network Time Protocol,TP393.05
  18. The wide input high gain Isolated DC-DC converter,TM46
  19. Research on Control System of Modular Multilevel Converter,TM464
  20. Design of Dynamically Self-adaptive Load Current Maximization Technique in PV Cell MPPT Systems,TM914.4
  21. The Research of Measurement Grounding Dc Resistance,TM934.12

CLC: > Industrial Technology > Electrotechnical > Transformers, converters and reactors > Converter
© 2012 www.DissertationTopic.Net  Mobile