Dissertation > Excellent graduate degree dissertation topics show

Numerical Simulation Analysis of the Three-Points Welding for Air-Conditioning Compressor

Author: WangZuo
Tutor: WuFengShun
School: Huazhong University of Science and Technology
Course: Materials Engineering
Keywords: air-conditioning compressor three-points welding welding deformation numerical simulation analysis temperature filed stress and strain field
CLC: TG44
Type: Master's thesis
Year: 2011
Downloads: 31
Quote: 0
Read: Download Dissertation

Abstract


Connect shell and pump using three-points welding in the air-conditioning compressor. Welding parts (flange in the CN series, cylinder in the CM series) deformation of pump after welding reduce the accuracy of the compressor assembly, lead to the performance and reliability of compressor is decline, compressor off the assembly line to scrapped in serious situation, cause huge economic losses. In the article, Numerical simulation analysis of the three-points welding for CN and CM series air-conditioning compressor by large commercial finite element software ANSYS and experimental verification of this simulation. On this based optimization of welding parts structure for CN series pump.The actual product due to the shell and pump is sealed, therefore, the results of numerical simulation of three-points welding is difficult to experiment validation. In the article, numerical simulation of the three-points welding for shell and welding parts of pump in first, and verified them by experiments, Use measurement of temperature by thermocouple and welding deformation for the key points of welding parts of pump method to verify the results of the simulation of three-points welding for shell and welding parts of pump. When the effective input power is 4000W, the effective heating radius is 0.009m, results of the simulation and experimental is consistent.On the basis of simulation and experimental works, Numerical simulation of a continuous (one-welding)and secondary (two-welding) three-points welding for CN series shell and pump, results show that one-welding deformation is smaller, And found on the bottom deformation of flange affected not only by three-points welding, but affected by screw preload is great. numerical simulation of three-points welding for CM series compressor in the one-welding process, found inner circle roundness of cylinder and vane groove deformation are significantly reduced.Numerical simulation of three-points welding for CN series different structures of flange, found non-pierced of the solder joint structure is the optimal structure, into the production of this structure, compressor off the assembly line to scrap rate reduction from the original 1.1% to 0.5%.

Related Dissertations

  1. Power factor correction technology and its inverter air conditioner system,TM925.12
  2. Study on Sensorless Switched Reluctance Drive System for Automobile Air Conditioning,U463.851
  3. Investigation of Interior Permanent Magnet Brushless DC Motor Sensorless Drive for Electrical Air-conditioning in Vehicles,U463.851
  4. Research of BLDC Motor Speed Control System Based on Sensorless Technology,TM33
  5. Used in air conditioning compressor drive brushless DC motor controller design,TM33
  6. Designed and Implemented of Automatic Measure Matching Device Ofthree-parts in Rotary Compressor,TH45
  7. Automotive Parts Project Feasibility Study and Case Analysis,F224
  8. Research of Frequency Conversion Air Conditioning Compressor Drive Technology,TM341
  9. SVPWM based on fuzzy control technology in the air-conditioning compressor inverter application,TM925.12
  10. Research on Low Friction Automobile Air Conditioning Parallel-moving Rotor Compressor,U463.851
  11. Finite Element Numerical Simulation of Key Parts in Automobile Air-condition Compressors,U464
  12. Anaysis of Temperature Field and Stress and Streain Field in Dual Beam Laser Welding Different Thickness Plates,TG456.7
  13. Development of Bus Interface Conversion Card of Automobile Air-conditioning Compressor Durability Test-bed,U463.8
  14. Study on the HCC Technology & Microstructure & Mechanical Properties of Cast Iron Bars Applied to Air-Condition Compressor,TG250
  15. Research on the Embedded-Vane Type Automobile Air-Conditioning Compressor,TB652
  16. Study on High Temperature Properties and Stress State of Slab,TF777
  17. Temperature Effect Research of Long-span Steel Box Girder Cable-stayed Bridge,U448.27
  18. Numerical Simulation of Extrusion Process of W-40wt.%Cu,TG379
  19. Study on Reservoir-induced Seismicity in the Subsequent Project of Danjiangkou Reservoir,TV697.2
  20. Fire temperatures CFRP reinforced concrete beams Temperature Field,TU375.1
  21. Analysis on Welding Residual Stress with ANSYS,TU391

CLC: > Industrial Technology > Metallurgy and Metal Craft > Welding, metal cutting and metal bonding > Welding process
© 2012 www.DissertationTopic.Net  Mobile