Dissertation > Excellent graduate degree dissertation topics show

Processing Tolerance Analysis and Optimal Design of MEMS Gyroscope

Author: PengShouJun
Tutor: WangWei
School: Xi'an University of Technology
Course: Optical Engineering
Keywords: MEMS gyroscope processing tolerance ANSYS simulation anti-overload optimal design
CLC: TH703
Type: Master's thesis
Year: 2011
Downloads: 85
Quote: 0
Read: Download Dissertation

Abstract


MEMS gyroscope has been applied widely in low precision inertial navigation and attitude determination systems for its smaller volume, lower power consumption, lower cost and some other features compared with traditional gyroscope. Measuring accuracy of MEMS gyroscope is great affected by bulk-silicon manufacture processing error, and the processing error effect on gyroscope performance is related with the gyroscope structure, so the analysis of processing tolerance and the gyroscope structure optimal design are very important.In this paper, the dynamic model of Z-axis linear vibration MEMS gyroscope was established firstly, and then the dynamic equations of drive and detect direction were attained by Lagrange Principle. Some coupling terms were discarded and the simplified kinetic equations of Z-axis gyroscope were achieved. The expression of driven displacement related with driving force, the quality factor, the mechanical sensitivity related with modal frequency, the bandwidth and other important gyroscope characteristics were obtained by solving the simplified kinetic equation. The drive and detection mechanism of electrostatic comb capacitive, electrostatic tuning, the support beam stiffness and its matrix expressions were analyzed overall.The theoretical error caused by coupling term can be ignored. Based on gyroscope dynamic and electrostatic drive theory, the effects on the gyroscope caused by center offset of mass, structure deviation of capacitor, structure deviation of beam and residual stress were analyzed. The expression of relative error and interaction term caused by processing error was listed.The model simulated calculation of important component and the entire gyroscope were done used ANSYS software. The model analysis of two folding support beam structures indicated that the stiffness of folding beam meet the design requirements; the simulation data of comb capacitor indicated that the capacitance is more sensitive for variation of comb width; the comb operated in normal voltage range can be anti-adsorption. The gyroscope mode analysis and stiffness calculations of 3D and 2D model show that gyroscope mode frequency satisfied matching constraints, stiffness meet the decoupling requirements and modal analysis of 2D have approximate result with 3D modal analysis. The overload results of 3D and 2D model show that the gyroscope anti-overload requirement has been satisfied.From relative processing error expression of different gyroscope structures, the interaction term expressions caused by process error, gyroscope simulation data and structural parameters combined with gyroscope technology targets, the different processing tolerance ranges were calculated.According to the gyroscope dynamics and simulation results, the major MEMS gyroscope performance requirements were determined. The target constraints and design constraints were both taken into account, the length and width of beam structure were set as design variables, the optimal design of gyroscope structure was completed based on different objective functions used optimal component in ANSYS.

Related Dissertations

  1. Finite Element Analysis and Structure Optimal Design for Combined Seal at Normal Temperature and Low Temperature,TH136
  2. Humaniod Robot Development and Research,TP242
  3. Dynamic Analysis and Optimization of Six-bar Beating-up Mechanism of an Air-jet Loom,TS103.33
  4. Structure Analysis and Optimization Design for 150 Tons Flat-Top Crane,TH213.3
  5. Optimal Design of Suspender Replacement in Concrete Filled Steel Tubulur Arch Bridge,U448.22
  6. Real-time medical ultrasound puncture navigation positioning and soft tissue modeling,R318.6
  7. Mold cavity surface MRF technology research,TG580.692
  8. Wavelet Analysis Based Signal Denoising Research in MEMS Gyroscope,TN911.4
  9. Simulation analysis and optimization design of pull arm garbage truck,U469.691
  10. The Structure Strength Analysis and Optimization Design of Impact Wheel for Impact Roller,U415.521
  11. Structural Analysis and Optimization Design for Single-girder Gantry Crane with Double Hook,TH213.5
  12. Structural Static Force Analysis and Optimum Design of High Pressure Vessel for CNG Based on ANSYS,TE972
  13. Theoretical study based on curvature modal bridge damage diagnosis Finite Element Analysis,U446.3
  14. Simulated Study of Temperature Control and Anticracking in Mass Concrete Pile Cap,U445.57
  15. The Main Beam of the 50t/28m Gantry Cranes’ Finite Element Analysis and Structural Optimization and Design,TH213.5
  16. Research and Relevant Design of Vibrating Ring MEMS Gyroscope,TN966
  17. MEMS Gyroscope High Precision Analog/digit Conversion Technique Based on Sigma-delta Theory,TN792
  18. The J compensation management system optimization study,F272.92
  19. Biomechanics Optimum Design and Analysis of All-ceramic Crown Based on Continuous Parametric Finite Element Method,R783
  20. Study on Multi-objective Optimization Design of a New Planetary Gearbox Based on the Fuzzy Reliability,TH132.46
  21. The Survey of Basket Electromagnetic Flowmeter Applied in High Water-Cut Oil-Water Two-Phase Flow,TH814.93

CLC: > Industrial Technology > Machinery and Instrument Industry > Instruments, meters > General issues > Structure
© 2012 www.DissertationTopic.Net  Mobile