Dissertation > Excellent graduate degree dissertation topics show

Study on the Geometric Structure and Mechanical Performance of Resistance Spot Welding Cold-rolled 301L Joints

Author: SunChuanJing
Tutor: LiuWei
School: Beijing Jiaotong University
Course: Materials Processing Engineering
Keywords: cold rolled 301L nugget diameter failure mode tensile shear strength fatigue limit
CLC: TG407
Type: Master's thesis
Year: 2011
Downloads: 46
Quote: 0
Read: Download Dissertation

Abstract


The traditional theory of spot welding technology are based on the research results of steady-state alloy, which believes the spot welding specimen’s carrying capacity is low and fracture absorbed energy is small when its fracture mode is interfacial fracture. Traditional theory proposes to use pull-out fracture mode which it thinks has better performance. The diameter of JIS Z 3140 recommended is d=5(?) which can make sure nugget achieve pull-out fracture. But to high-strength 301L cold-rolled sheet, specimens with the diameter of JIS Z 3140 recommended can’t achieve pull-out fracture, and the strength of pull-out fracture does not higher than the strength of interfacial fracture.In this thesis, the research objects are the main bearing spot-welded joints of the railway stainless steel car body. Resistance spot welded tensile shear specimens with three nugget diameters 5(?)、6(?)、7(?) were prepared with low and high strength cold-rolled 301L plates. The static overload and fatigue examinations of the spot welds were conducted to investigate the effects of nugget diameters on their mechanical properties and failure mode.The results showed that, to 301L cold rolled plate, static tensile shear strength increased with nugget diameter and the weld defects had little effect to the value of static strength. All spot welded high strength plates were completely interfacial failure, and their static ultimate loads increased linearly with the nugget diameters. Only part of spot welded low strength plates with nugget size 7(?) came out pull-out failure, the ultimate loads were lower than that of those fractured by interfacial failure. Anti-fatigue properties of four combination samples increased with nugget diameter and this effect in thick plate spot welding was more obvious. The spot welding samples which nugget diameter of 6(?) had better performance of technology and machinery. Doing system of static shear and fatigue tests with these samples to research deformation behavior and fatigue limit of different combinations of plate and reliability of spot welded joint. The research data and results can provide the basis reference for the design and manufacture of stainless steel car.

Related Dissertations

  1. Key Technologies of Dam-break Life Loss Risk Assessment Research,TV122.4
  2. Fracture mechanics studies of industrial structural steel fatigue limit,TG142.1
  3. Collapse Modes, Risk and Robustness Analysis of RC Frame Structures,TU375.4
  4. Research of Inverter Resistance Spot Welding Process of High Strength Dual-phase Steel,TG453.9
  5. Fatigue Performance and Heat Stability of High-Strength Heat-Resistant Aluminum Alloy,TG146.21
  6. Research of Influence on Quality in Resistance Spot Welding Automobiles Galvanized Steel,TG453.9
  7. Study on Synthesis and Properties of Room Temperature Curing Conductive Adhesive,TM24
  8. Analysis on the Failure Mechanism of Composite Ground under Flexible Foundation,TU473.1
  9. Study on Bearing Behavior and Optimum Design of Rigid-pile Composite Foundation,TU473.1
  10. Hole castellated beams hysteretic behavior and failure mode analysis,TU312.3
  11. Experimental Study on Static Performance of Steel Beam to Concrete-Filled Double Skin (CHS Inner and CHS Outer) Steel Tubular Columns,TU398.9
  12. Three- ply puncture progressive damage analysis of composite materials,TB332
  13. Circular truss deployable satellite antenna Reliability Research and Analysis,TN828.5
  14. 3F technology in UAV flight control system applications,V279
  15. Experimental Study on the “Y”–type Tubular Joints with Cross-weld,TU392.3
  16. Ultimate Strength of Gusset Plate of Steel Tubular with Gusset Plate Connections,TU391
  17. Investigation on the Reliability of Copper Ball Bonding in Power Devices Packaging,TN405
  18. Cellular Automata Technique for Predicting Failure Pattern of Wall Panel Based on Experimental Records,TP23
  19. The SVM Technique for Predicting Failure Mode of Masonry Panel,TU317
  20. CFT column two limbs improved carrying capacity single girder webs shoulder Study,TU398.9

CLC: > Industrial Technology > Metallurgy and Metal Craft > Welding, metal cutting and metal bonding > Welding general issues > Mechanical properties of welded joints and Intensity
© 2012 www.DissertationTopic.Net  Mobile