Dissertation > Excellent graduate degree dissertation topics show

Optimal Design of Dynamic Response for the Wind Turbine Blade

Author: GanWenYan
Tutor: QiuPing
School: Lanzhou University of Technology
Course: Engineering Mechanics
Keywords: wind turbine blade ANSYS modeling mode analysis optimization design
CLC: TK83
Type: Master's thesis
Year: 2011
Downloads: 126
Quote: 0
Read: Download Dissertation

Abstract


Due to the world-wide economy development, the problem of shorting energy resources has caused more and more attention. The world-wide gazed on renewable energy, so the renewable energy get an unprecedented development. The wind energy is a kind of clean renewable green energy which obtained a rapid development. Many countries in the world focused on the development and utilization of wind energy, using wind turbines to convert wind energy into electricity. China, as the energy consuming countries in recent years, wind power industry developed to a certain scale, but on the wind power technology, China’s wind power technology backward than the the developed countries. In particular, as one of the key components of wind turbine blade technology. Therefore, to accelerate the localization of wind power technology to improve the technological level of China’s wind power a top priority. The blades, the key part of the wind turbine, were studied in this article. The main conclusions are as follows:1.According to the reading the vast literature, introduced the development of domestic and international wind turbine blades statue and technology development, and discussed the wind machines basic concept. Expounds the Finite Element Analysis (FEA) theory of blade’s structure to modeling for 1.2MW wind turbine blades.2.ANSYS modeling of blade. According to the geometry parameters of blade to receive specific section of the coordinates of the point of blade element, use of office software Excel coordinate conversion, obtained three-dimensional coordinates of the points blade. Using the three-dimensional modeling software ANSYS for solid modeling for further analysis3.Blade on the solid model has been built using the finite element analysis software ANSYS vibration modal analysis. Calculated natural frequency and analysis of the vibration modes and the relative stress of each mode.4.According to the structural analysis results, the geometrical shape of blade optimized design, and optimized blade is analyzed. The results proved the optimized blade has more advantages. This explains the optimization scheme basically is rational and feasible, and has certain applicability.

Related Dissertations

  1. Development of the Platform for Compressor Optimization Design and Aerodynamic Optimization Design in the Transonic Compressor,TH45
  2. Investigation of Turbine S2 Stream Surface Direct Problem Aerodynamic Optimization Design,V235.11
  3. The Dynamic Performance Analysis of Oil Pumping Center and Structural Optimization of Improvement,TE933.1
  4. Finite Element Analysis and Optimization Design of a Tractor Cab,S219.02
  5. Medical Application of a Wireless Communication Platform Based on RFID and GPRS,R319
  6. The turbofan engine pneumatic runner Optimization Approach,V235.13
  7. The Optimization Design and Discusses of Weft Flexible Complex Stab-Resistant Layers,TS186.2
  8. Small Wind Turbine Blade Design and Simulation Analysis,TM315
  9. Structure Analysis and Optimization of a Reducer,TH132.46
  10. Research of Dynamic Distortion on a Ship Based on the Theory of Hydroelasticity,U661.1
  11. Strength Research and Design Optimiazation for Ply Stucture of Wind Turbine Blade,TM315
  12. Concrete Tied Arch nonlinear mixed- discrete variables optimization design,U448.225
  13. Study on Designing Agricultural Product Supply Chain Network,F323.7
  14. The Research on Mine Fan and Its Key Parts,TD441
  15. Optimization Design of Reinforced Structural for Sheared Ringent Composite Laminate,TB33
  16. Plastic Mold Design of the Automobile Plastic Box Based on the CAD/CAE Software,U463.83;TP391.7
  17. Structural Strength and Vibration Analysis of the Turbo-generator Stator,TM311
  18. Study on Optimization Design of Electric Power Line Based on Visualization Technology,TM75
  19. Study on Characteristics of Inter-area Low Frequency Power Oscillation in Interconnected Power Grid,TM712
  20. Study on Structural Dynamic of Large Turbine Blade of SMA Composite,TK83
  21. Study of the MHD Instabilities on SUNIST Spherical Tokamak,TL631.24

CLC: > Industrial Technology > Energy and Power Engineering > Wind energy, wind machine > Wind machinery and equipment
© 2012 www.DissertationTopic.Net  Mobile