Dissertation > Excellent graduate degree dissertation topics show
Multi-output switching power supply design
Author: HouYu
Tutor: YangBing
School: North China University of
Course: Signal and Information Processing
Keywords: Current-mode Synchronous step-up controller Chargepump
CLC: TN86
Type: Master's thesis
Year: 2009
Downloads: 508
Quote: 1
Read: Download Dissertation
Abstract
|
With the wide use of portable electronics, multifunction is one of characteristics for portable electronics, which encounters some challenges. Switching voltage regulator, with its distinctive features of high level of integration, simple peripheral circuit and high efficiency, has been widely used in many electronic products. Core unit-control circuit integration of the switching power supply has been one of switching power supply development for many years. A smaller volume, the less EMI, over current and over voltage protection circuit technology has been developing in this process.In this thesis, a high-performance step-up DC-DC power converter is proposed. It is a complete power converter solution used for a small thin-film transistors liquid crystal display. It may use the single-cell lithium battery, 2 to3 alkaline batteries input or operate any voltage source between the 1.5 V and 4.6 V. Chapter I is introduction, which introduce the development of power management chips and related technology developments, as well as the arrangement of the paper; Chapter II presents the system architecture as well as the charge pump, and the operating principle of synchronous boost converter;the third chapter is devoted to sub-module design and simulation results; The fourth chapter describes the circuit layout of the whole system ;Chapter V of this paper summarizes the content.The chip input operating range is 2.7V～5.5V.Synchronous step-up controller can generate a low-noise, high efficiency power of 5.1v.The internal charge pumps used to generate 10V, 15V and-5V,-10V or-15V voltage. Based on the0.6um CMOS process simulation model and using the tools of Hspice, every sub-block has been simulated to ensure that its power and temperature at different targets to achieve the design requirements.
|
Related Dissertations
- Low-power, low-voltage Peak Current Mode Boost Converter stability and Design,TM46
- A SIMO power management chip design based on computer-aided software,TN492
- Design and Research of a Current Mode DC-DC Converter Chip,TM46
- Design of Dynamically Programmable High Efficiency Synchronous Buck Converter IC,TM46
- High-Speed and Low-Power Ternary Logic Circuits Design Based on MCML/TG,TN432
- Design of Low Power Dissipation PWM Current Mode (AC/DC) Power Controller,TM571
- Optimization of Control Circuit Used in Peak Current-mode Converters,TM46
- Single-stage power factor correction AC / DC converter research,TM46
- Analysis and Design of a DC-DC Buck Converter for Portable Battery-Operated System,TM910
- One kind of mains -powered white LED driver circuit control chip design,TN432
- Design of PWM DC-DC Buck Switching Converter Based on Current-mode Technology,TN86
- The Research & Design of High-Efficiency Synchronous Rectification Buck DC/DC Conversion,TM46
- Design of High Efficiency Peak-Current-Mode Boost DC-DC Converter XD1620 IC,TM46
- BCD process based on white LED driver design,TN312.8
- Design of BOOST DC-DC Converter with Peak Current-mode PWM Control,TM46
- Ultra-wideband wireless communication system low wide ultra high-speed ADC design,TN792
- Modeling System of Current-Mode-Controlled Boost Converter and Design of the Controller,TM46
- The Design of the Synchronous Rectification Buck DC-DC Converter Based on Peak Current-Mode,TM46
- Design of a Low-power Boost DC/DC Converter with Selectable Current Limit,TM46
- Based on the third generation current conveyor current-mode filter design,TN713
CLC: > Industrial Technology > Radio electronics, telecommunications technology > Radio equipment,telecommunications equipment > Power supply
© 2012 www.DissertationTopic.Net Mobile
|