Dissertation > Excellent graduate degree dissertation topics show

Study on FGD Gypsum-based Aerated Concrete

Author: KongXiangXiang
Tutor: ChenYouZhi
School: Wuhan University of Technology
Course: Building materials and engineering
Keywords: FGD gypsum FGD gypsum-based binder aerated concrete non-autoclaved energy-saving
CLC: TU528.2
Type: Master's thesis
Year: 2009
Downloads: 441
Quote: 5
Read: Download Dissertation

Abstract


The FGD gypsum-fly ash products has good performances such as energy-saving,using waste,environmental protection,insulation and so on.FGD gypsum-based binder has obtained extensive research.Aerated concrete has been concerned about increasingly because of its outstanding merits such as light weight, using waste,heat preservation and energy-saving.But the present aerated concrete was produced in the condition of autoclaved,the process is complex and it will use a lot of energy.In order to achieve the develop target of the wall material,it is necessary to research and manufacture FGD gypsum-based non-autoclaved aerated concrete.In this paper,the effects of mix ratio,w/c ratio,slurry temperature and curing conditions on compressive strength,bulk density and pouring stability of non-autoclaved aerated gypsum-based concrete were studied by experiments in the technology of non-autoclaved conditions.Eventually show that the rational content of FGD gypsum is 50～70%.The optimal content of fly ash is 25～30%;The maximum addition of cement clinker is 20%;The optimal content of lime is 8～12%; The best content of aluminum is 0.13%,and the amount of aluminum should be considered together with w/c ratio;The best w/c ratio is 0.47～0.50;Slurry temperature was controlled at 28～32℃.Heat conservation methods in 50～75℃is the best curing mode of FGD gypsum-based aerated concrete.Select reasonable ratio can get FGD gypsum-based aerated concrete that the compressive strength up to 2.8～3.3MPa and the bulk density can controlled under 750kg/m3.In this research,the production craft of products was studied.Through the experiments,it is obvious that some factors have effect on the property of gypsum-based aerated concrete in some degree,such as the sequence of commixing the slurry,the time control of mixing process.Through XRD and the SEM microscopic test methods,the microstructure and hydration mechanism of gypsum-based aerated concrete harden has studied.The result indicated that,the mainly hydration products are:CaSO4·2H2O,Aft and C-S-H.The crystalline state of hydrated product are better,a homogeneous and densified microstructure of aerated concrete was obtained.Used FGD gypsum and fly ash to prepare non-autoclaved aerated concrete in the lab is an innovative of FGD gypsum-based binder,which can save the equipments investment,reduce the consuming of energy.If it can be applied in the industrial production,it will not only benefit from the utilization of solid waste disposals and environmental protection,but also prominent economic benefits and social benefit,it is of far-reaching significance and great.

Related Dissertations

  1. Several Problems of Energy Saving Operation in Air Conditioning System of Large Scale Public Buildings,TU831.6
  2. Research on University’s Energy Saving System Facing the Construction of Green University,G647
  3. Applied Research of Emulsified Fuel on S195 Diesel Engine,TE626.24
  4. A Research and Development for Single Chip Micyoco AVR Usage,TP368.12
  5. Location Assisted Wi-Fi Discovery on Mobile Devices for Energy Saving,TN929.53
  6. Saw motor energy-saving controller for tilting sand stone processing DSP-based research and development,TM343
  7. Research on Evaluation of Coal Enterprise Energy-Saving Mechanism,F206
  8. Study on Green Finance Promotes Industrial Restructuring,F832;F205
  9. Stainless Steel Bright Annealing Furnace with Waste Heat Recovery Energy-saving Technology Research,TG155.1
  10. On a New Type of Building Walls-photoelectric Curtain Wall,TU228
  11. The Research and Implementation of Energy-efficient RAID,TP333
  12. The ethylene energy optimization management system design and implementation,TP311.52
  13. Study on a Bathroom Heating Plan of Utilizing Renewable Energy Source,TU833
  14. Very large crude oil tankers overall energy efficiency design key technology research,U662
  15. Research on Utilizing Braking Energy in the State of Vehicle’s Deceleration and Light Load Conditions,U461
  16. Research on Control System of Hot-reclaimed Asphalt Pavement Maintenance Vehicle Based on PLC,U418.6
  17. Under the Condition of Gansu Province Regional Highway Toll and Affiliated Facilities Construction,U417.7
  18. Research on Power Monitoring and System Control of Hydraulic Power System Based on Virtual Instrument,TH137
  19. Wireless sensor network MAC protocol,TP212.9
  20. Decompose Energy-saving Index Research and Analysis Based on Analytical Hierarchy Process (AHP),F224
  21. The Study on Hydraulic Balancing Optimization of Fluid Pipeline Network,TV134

CLC: > Industrial Technology > Building Science > Building Materials > Non-metallic materials > Concrete and concrete products > Lightweight concrete
© 2012 www.DissertationTopic.Net  Mobile