Dissertation > Excellent graduate degree dissertation topics show

Study on Technique Optimization and Microstructure Property of 5083H116 Alloy Sheet

Author: ZhangZuo
Tutor: HuangGuangJie
School: Chongqing University
Course: Materials Science and Engineering
Keywords: 5083 H116 Aluminum Alloy Rolling Stabilizing Treatment Intergranular Corrosion Exfoliation Corrosion
CLC: TG339
Type: Master's thesis
Year: 2009
Downloads: 209
Quote: 0
Read: Download Dissertation

Abstract


The 5083 aluminum alloy belongs to the series of Al-Mg which is a deformation alloy and can not be strengthened by heat treating. It is widely used in shipbuilding industry. In this paper, the behavior of 5083 aluminum alloy during hot compression deformation have been studied by means of the isothermal compression simulation test. The effect of different rolling and stabilizing treatment conditions on the microstructure, mechanical properties, and corrosion properties of the 5083 aluminum alloy sheet is discussed by a series of tests and studies. Such as orthogonal experimental design, testing mechanical properties test, scanning electronic microscope (SEM), energy dispersion spectrum (EDS), metallographic microscopy, intergranular corrosion test and exfoliation corrosion test, polarization curve determination and so on. The optimum 5083 alloying component content is obtained according to the above experimental result.The optimization of production process of the 5083 H116 alloy sheet is improved. The results show that:①The stress raise with the increase of strain rate at the same compression temperature, which show 5083 aluminum alloy is positive strain rate sensitivity material, the stress raise with the reduction of compression temperature at the same strain rate. Deforming degree has little effect on the stress at the same strain rate and the same compression temperature.②The anti-corrosion properties of 5083 alloy have great effect on cold deformation and stabilizing treatment process, the intergranular corrosion and exfoliation corrosion of the 5083 H116 alloy sheets tend to raise with the increase of cold deformation and the reduction of stabilizing treatment temperature. The mechanics of intergranular corrosion and exfoliation corrosion of the alloy were analyzed.③The poor corrosion resistance results from a continuous network ofβ-phase and along the planes of localized deformation in alloy after cold-rolled and stabilizing annealing below130℃. The high corrosion resistance of the cold-rolled alloy stabilizing annealing at 220～250℃is relate to discontinuousβ-phase precipitation uniformly distribute throughout the structure in a globular form. The poor corrosion resistance of cold-rolled alloy stabilizing annealing at higher temperature is attained because of a continuous network ofβ-phase precipitates at boundaries.④Through 5083 alloy component proportion experiment,compare the influence on mechanical properties and anti-corrosive performance of 5083 H116 alloy sheets with different percentage of the element content in order to confirm the best component matching of 5083 alloy. The optimum cold deformation, annealing temperature and time were presented.

Related Dissertations

  1. Study on Contact Fatigue Life Based on Grease Variation with Temperature,TH117.22
  2. Research on Caster Oil-based Cold Rolling Oil,TE666
  3. Research on Processings and Microstructure and Properties of HRB400MPa,TG335
  4. Band Entropy Method and Its Application to Fault Diagnosis of Rolling Bearings,TH165.3
  5. Data Driven Rolling Bearing Fault Diagnosis Research,TH165.3
  6. Regional reconnaissance UAV Route Planning,V279.3
  7. Study on Forecasting Methods of Rolling Bearing Friction Torque,TH133.33
  8. Experimental Data Analysis of Rolling Bearing Friction Torque,TH133.33
  9. First-Principles Study on the Properties of δ and γ" Phases and the Recrystallization Behavior of Cold Rolled INCONEL 718 Super-Alloy,TG111.7
  10. Experiment and Research on Rolling Lubricant Technology in Hot-strip-finishing-mill Meishan-Steel,TG333
  11. Study on the Toughness of X80 Pipeline Steel,TG142.15
  12. Rolled magnesium alloy ratcheting behavior and microstructure simulation,TG339
  13. Manganese steel cold rolling reverse transformation and mechanical properties of annealed,TG335.12
  14. Rolled Mg-Zn-Ce-Zr (Mn) alloy microstructure and mechanical properties of,TG339
  15. 316LN austenitic stainless steel stress corrosion cracking of welded joints,TG407
  16. Research on Automatic Gauge Control of 2300 Hot Rolling,TG334.9
  17. Textures of Magnesium and AZ31 Magnesium Alloy Processed by Unidirectional Rolling,TG339
  18. Research on Cold Rolling Niobium and Titanium Short Slab with Tension,TG335.12
  19. Study of Automatic Gage Control System of Single-Stand Four-High Aluminum Strip Cold Mill,TG334.9
  20. Large rolling synchronous motor damper bar Failure Analysis and Countermeasures,TM341
  21. Study on Technology of Flying Gauge Change and Thickness Preset for Tandem Cold Mill,TG335.12

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metal pressure processing > Rolling > Non-ferrous metal rolling
© 2012 www.DissertationTopic.Net  Mobile