Dissertation > Excellent graduate degree dissertation topics show

Studies comparing CSP process with conventional hot strip organizational performance

Author: ZhangXiaoMing
Tutor: WuZuo
School: Nanjing University of Technology and Engineering
Course: Materials Science
Keywords: CSP Process Traditional Process Low-carbon Hot-rolled Plates Yield Strength Ratio
CLC: TG335.11
Type: Master's thesis
Year: 2009
Downloads: 281
Quote: 2
Read: Download Dissertation

Abstract


CSP production line, as enjoying the advantages of low investment, short period, high efficiency and low cost advantages, has been adopted and applied by more and more hot-rolled plates’ manufacturers. However, due to the differences on metallurgical processes, materials’ metallurgical solidification process characteristics, phase change and technology process of CSP technology with those of traditional thick slab production processes, it is usually resulted in higher yield strength and higher yield strength ratio in low-carbon hot-rolled plate by CSP technology, which has lead to difficulties in following cold-rolling process. Therefore, it is quite meaningful to find the differences between mechanical properties and microstructure of the low-carbon hot-rolled plates made by the two technologies, which has also made sense to the manufacture technique improvement of low-carbon hot-rolled plates.Based on the analysis of mechanical properties and microstructure in low-carbon hot-rolled plates produced by these two processes, the results are as follows: it has resulted in higher yield strength and higher yield strength ratio of low-carbon hot-rolled plates by CSP process as compared to the traditional process, as well as lower ductility than that manufactured by traditional process, which is consistent with the problems appeared during the practical production; the reasons for which, ferrite grain size is not the main reason, but the distributions of grain size, pearlite morphology, grain orientation and texture have played an part on the difference to a certain extent.By the methods of hardness measurements and microstructure observations on cold-rolled steel plates annealed at different temperatures, we finally make certain that the recrystallization temperature of the cold-rolled steel plate is 575℃with an under-pressure rate of 60%. And through different annealing processes, it has been also find out that annealing temperature does have but very little impact on the mechanical properties of the cold-rolled steel plate with an under-pressure rate of 60%.

Related Dissertations

  1. Effects of Bath Annealing Process on Microstructure and Mechanical Properties of Cold-Rolling Steel Sheet SPCC,TG335.55
  2. Study on Key Technique for Improving Traditional Technology of Roast Sheep Leg of Mongolia Special Food,TS972
  3. The Research on Virtual Machine Based-on Xen,TP302
  4. Study on New Process for the Preparation of Wine from Glutinous Rice,TS262
  5. Study on Finishing Temperature Control Model for Hot Strip,TG335.11
  6. Study on A Reduction-bonding Process for Manufacturing Stainless Steel Clad Strip,TG335.11
  7. Flexible Manufacturing Technologies of 345MPa～460MPa Grade High Strength and Low-alloy Steel Plates,TG335.11
  8. Development of Hot-rolled and Ribbed Round Steel Bars 25CrMoA for Ultra-high Strength Oil Sucker,TG335.11
  9. Study on Microstructure and Texture during Hot Rolling and Normalizing of Twin-roll Cast Silicon Steel Strip,TG335.11
  10. The Study on Re-dissolution and Precipitation Behavior of Second-Phase Particles in High Strength Hot-rolled Dual-phase Steel,TG335.11
  11. Investigation of High Strain and Low Cycle Fatigue Behaviors of Hot Rolled and High Strength H-beam Steels,TG335.11
  12. Heating system and hot deformation parameters on the microstructure and properties of X80 pipeline steel impact study,TG335.11
  13. The PQ600 high strength engineering machinery steel hot rolling process research,TG335.11
  14. Micro- alloying elements in the hot rolling process numerical simulation of elution,TG335.11
  15. Research and Design of Hot Strip Laminar Cooling Control System,TG335.11
  16. Pipeline steel and hot-rolled steel plate texture anisotropy studies,TG335.11
  17. H - section steel hot rolling temperature field and rolling force simulation,TG335.11
  18. Data mining in hot rolled plate with the application of quality prediction,TG335.11
  19. Simulation and Prediction of Microstructure and Properties of Hot-rolled Steels Based on Physical Metallurgy and BP Neural Network,TG335.11
  20. Coupled Numerical Simulation of Velocity and Temperature Field in Flat Hot Rolling Process,TG335.11
  21. Emulation Study and Mathematical Modeling of Laminar Cooling for Hot Strip Mill,TG335.11
  22. Studies on Oxidation Kinetics and Thermal Treatment Process of Hot-rolled Steels,TG335.11

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metal pressure processing > Rolling > Rolling process > Rolling method > Hot-rolled
© 2012 www.DissertationTopic.Net  Mobile