Dissertation > Excellent graduate degree dissertation topics show

Study on the Dynamic Recrystallization Behavior and Prediction Model of TA15 Titanium Alloy in the β Hot Process

Author: WuChao
Tutor: LiuZhiHe；LuShiQiang
School: Nanchang University of Aeronautics and
Course: Materials Processing Engineering
Keywords: TA15 titanium alloy βhot process dynamic recrystallization prediction model microstructure
CLC: TG111.7
Type: Master's thesis
Year: 2009
Downloads: 414
Quote: 6
Read: Download Dissertation

Abstract


TA15 titanium alloy is the one of the most important structural materials in the aircraft industry of our country which belongs to a kind of damage tolerance alloy of high aluminum equivalent. Because this alloy would easily appear“grain coarsening”phenomena duringβhot process, while utilizing dynamic recrystallization to control grain size in material microstructure is the key to solve the problem mentioned above. Therefore, in order to systematically obtain the evolution of dynamic recrystallized microstructure of TA15 titanium alloy inβhot process, and then to achieve a good matching between strength、plasticity and damage tolerance properties and guide practical production as well, the dynamic recrystallization behavior and prediction model of TA15 titanium alloy inβhot process have been studied by using isothermal constant strain rate compression tests and metallographic analysis system. The main research contents and conclusion are as follows:The true stress-true strain curves of TA15 titanium alloy compressed under various strain rates have been analyzed, and the results show that the flow stress is sensitive to the strain rates, when the strain rate increases one order of magnitude, the peak stress would increase about 5～20MPa; the rheological curves of low strain rates (0.001s-1, 0.01s-1) belong to the type of dynamic recrystallization, and its main softening mechanism is dynamic recrystallization, while the rheological curves of high strain rates (0.1s-1, 1s-1) belong to the type of dynamic recovery, and its major softening mechanism is adiabatic effect.The microstructures of TA15 titanium alloy samples compressed under different strain rates and deformations were observed and measured by using metallographic analysis system. The results show that increasing strain rate could refine grain obviously, but different strain rate would bring different degree of grain refinement, the grain size would decrease faster when the strain rates are in the low (0.001s-1, 0.01s-1), and on the contrary decrease slower in the high (0.1s-1, 1s-1) ; according to the effect of grain refinement and uniformity in the microstructures which deformed under various conditions, the strain rate of 0.01s-1 is preferable forβhot process; the deformed microstructures of TA15 titanium alloy inβhot process would mainly occur discontinueeous dynamic recrystallization under the lower strain rates, while it mainly occurs continuous dynamic recrystallization during the higher strain rates.According to the theory of recrystallization grain nucleation and growth as well as the basic characteristics of recrystallization kinetics, the theoretical mathematic models of dynamic recrystallization were derived, and base on the results of them the dynamic recrystallization prediction models of TA15 titanium alloy at temperature 1050℃were established firstly. The results indicate that the deformation activation energy of TA15 titanium alloy inβhot process is 313.442kJ/mol, and the relation equation between critical strainεc and peak strainεp isεc=0.8455×εp; the calculation formula of critical strain of dynamic recrystallization isεc =0.1245×Z0.0718, and among which symbol Z represents Zener-Holloman parameter equation; the concrete expression formula of average grain size of dynamic recrystallization is as follows: d=10.8134×Z-0.3261μm; and the expression formula of dynamic recrystallization kinetics is as follows: Xdyn=1-exp[-0.1146×（ε-εc）/εp]1.1998.

Related Dissertations

  1. Reactive Hot-Pressing and Mechanical Properties of （ZrB2-ZrO2）/BN Composites,TB332
  2. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  3. Study on Quality Change and Prediction Model for Shelf-life of Chilled Pork,TS251.4
  4. Study on Quality Changes and Firmness Prediction Model of Loquat Fruit after Harvest,TS255.4
  5. A Study on the Predictive Model of Health Assessment in Li River, Guiling, Guangxi,X826
  6. Predicting Wheat Grain Yield and Quality Based on Population Indexes and Nitrogen Nutrient Status,S512.1
  7. Genetic Dissection and Elite Allele Identification of Seed Traits in Soybean Cultivars Released from Huanghuai Valleys and Southern China,S565.1
  8. A Photo-Thermal Model for Predicting Growth and External Quality of Dendrobium Nobile in Greenhouse,S682.31
  9. Studies on Changes of Quality Characters and Prediction Model of Postharvest Tomato Fruit,S641.2
  10. Studies on Prediction Models for Fruit Decay and Shelf-Life of Postharvest Chinese Bayberry,S667.6
  11. Multi-Unidimensional IRT Model and Its Application,O212
  12. Study on the Hot Deformation Behavior and Processing Map of TC21 Alloy,TG146.23
  13. The Research on Sulfur Content Prediction Model for LF,TF769
  14. Research on Moving Object Detection and Tracking Algorithm in Video Surveillance,TP391.41
  15. Study on Microstructure and Performance of Laser Cladding Ni-Based Amorphous Alloy Coatings,TG174.4
  16. Research of Safety Stock Prediction Model Based on Improved BP Algorithm,O227
  17. The Preparation, Microstructure and Propertities of the New Type 3D-Meshy SiC/Cu-Fe Composite Material,TB33
  18. Study on Hot Deformation Behavior and Microstructure-Mechanical Properties of Cr12MoV Steel,TG142
  19. Study on Specialized Technical Indicators Evaluation System of Chinese Excellent Women’s Shot Putters,G824.1
  20. Traffic Prediction Model Based on Wavelet and Markov,TP393.06
  21. The Effect of Rare Earth Additive on the Structure and Property of the Steel for 25crmoa Sucker Rods,TG142.13

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > Metallurgy ( Physical Metallurgy ) > Physics of metals > Plastic deformation of metals,recovery and recrystallization
© 2012 www.DissertationTopic.Net  Mobile