Dissertation > Excellent graduate degree dissertation topics show

Study on Microstructure and Rheological Behavior of In-stu Mg2Si/AM60 Composites

Author: LiuZuoZuo
Tutor: ChenGuoXiang;ZuoHong
School: Nanchang University
Course: Materials Processing Engineering
Keywords: In-situ Mg2Si/Mg Modification Semi-solid Rheological behavior
CLC: TB33
Type: Master's thesis
Year: 2009
Downloads: 54
Quote: 0
Read: Download Dissertation

Abstract


Magnesium matrix composites have been widely used in spaceflight, mechanical electron, automobile manufacture etc. because of their low density, high specific strength and rigidity and good damping capacity.Mg2Si/Mg composites were prepared by in-situ reactive synthesis technique in this essay. The effects of Si content on the microstructure and mechanical properties of Mg2Si/Mg composites were systemically studied, and the modifying effect of Sb mischmetal on Mg2Si phase in the composites was also studied.The results show that, with the increase of Si content, the amount of Mg2Si in the solidified samples increases, and its shape becomes more full Chinese script. The tensile strength of 3% Si content was up to 181.7MPa which was more about 14.9% than that of the matrix. However, it would decrease while Si was increased continuously. When 0.8 wt. % Sb was added into the alloys, the shape of Mg2Si could be transformed from the Chinese script into uniformly dispersed particles. Therefore, Mg2Si/Mg composites with more desirable microstructure can be obtained.Semi-Solid processing has been attracting considerable interest for its well newly net forming, lower energy consumption and low pollution. Combined semi-solid processing and in-situ reactive synthesis technique, the semi-solid Mg2Si/Mg slurry was isothermally stirred to study the effect of processing parameters on the rheological behavior and microstructure by the self-made mechanical stirring equipment. Semisolid rheological forming and the microstructure evolution rule of Mg matrix composites were discussed in this paper.The results show that, the microstructure of composites changed gradually from dendrite to rose-shaped, finally to be non-dendrite or spheroid-shaped as the increasing of shearing rate and shearing time. The apparent viscosity increased with increasing of Si content and solid fraction, while decreased with the increasing of shearing rate and shearing time. However, the apparent would not reduce after shearing over 300s but went to be a stable value.

Related Dissertations

  1. Optimizition of Compositions and Processing Parameters and Wear Properties of Cemented Carbides YG11R Modified by Nanosized Rare Earth,TG135.5
  2. Research of High Speed Image Pre-processing System Based on FPGA,TP391.41
  3. Preparation of Crop Stalk-Based Sorption Materials with High Performances and Their Applications for Pah Removal from Water,X712
  4. Synthesis and Biocompatibility of different types of hydrophilic surface - modified polyurethane,R318.08
  5. Polyaniline / short fiber reinforced natural rubber properties,TQ330.1
  6. Phosphate modification of nano- TiO 2 Photoelectrochemical Properties of the,TB383.1
  7. Construction of Multi-responsive Gene Vector Via Layer-by-Layer Assembly,TB383.1
  8. Study on Kevlar Fibers/bismaleimide Resin Composites,TB332
  9. The Study of Li-rich Layered Solid-Solution Cathode Materials for Lithium Ion Batteries,TM912
  10. Progress of Research on the Visible Luminescence Mechanism of ZnO,O472.3
  11. Study on Sulfonation Surface Treatment of Plasma Alkali Secondary Battery Separator,TM910.5
  12. Study on Laser Surface Modification of Two Kinds of Super-alloys,TG174.4
  13. Chengdu Electric Power Performance Management Information System Design and Implementation,F426.61
  14. Reaction Sintering Preparation of Titaniferous Compound Ceramic Composites by Two-step Method,TQ174.1
  15. Atmospheric Pressure Plasma Surface Modification of Carbom Fibers and Numerical Simulation of the Discharge,TQ342.742
  16. Study on Modification of PBO Fibers by Atmospheric Pressure Plasma,TS195.6
  17. Study on Preparation and Stability of Allicin Lipsomes,TS255.1
  18. Surface Modification of Poly (ε-caprolactone)s and Its Influence on Cell Behaviour,R318.08
  19. Stainless steel fuel cell bipolar plate and its experimental and simulation,TM911.4
  20. Nuclear Power Plant Steel Milling Surface Integrity Study,TG54
  21. Atmospheric pressure pulsed RF plasma discharge for high strength and high modulus polyethylene fiber surface modification,TQ342.61

CLC: > Industrial Technology > General industrial technology > Materials science and engineering > Composite materials
© 2012 www.DissertationTopic.Net  Mobile