Dissertation > Excellent graduate degree dissertation topics show

The end of 7050 aluminum alloy quenching quenching studies Permeability

Author: ZhangYong
Tutor: DengYunLai
School: Central South University
Course: Materials Processing Engineering
Keywords: 7050 aluminum alloy Thick plate Quench sensitivity Hardenability heat-transfer coefficient Microstructure
CLC: TG166.3
Type: Master's thesis
Year: 2008
Downloads: 345
Quote: 10
Read: Download Dissertation

Abstract


7050 aluminum alloy is an Al-Zn-Mg-Cu-based high strength alloy developed by replacement of dispersoid-forming Cr and Mn with Zr and changing contents of Zn and Mg in the 7075 aluminum alloy in the 1970s. Typical applications for 7050 Al alloy thick plate are fuselage frames and bulkheads in active service large airplanes.It is a key to control penetration as quenching（hereafter hardenability）because of its quench sensitivity.However,there is few literature quantitatively reports the hardenability about 7000 series aluminum alloy.In fact,the quantitative hardenability is very important to maximize magnitude properties and uniformity of microstructures and minimize residual stress in quenched high strength aluminum alloy thick plate.In present paper,a demonstration quenching testing system of Jominy End Quench method adapts to aluminum alloy materials is established. Hardenability of samples cut from a 7050 Al alloy hot-rolled thick plate is investigated by testing the hardenability curves after being quenched by spraying various reagents.The microstructures of different cooling rates are characterized by optical microscopy（OM）,scanning electron microscopy（SEM）and transmission electron microscopy（TEM）.As a result,the conclusions can be gotten:（1）The demonstration method of non-linear relationship between surface heat-transfer coefficient and temperature of the sample has been established.This non-linear surface heat-transfer coefficient by spraying water at 20℃is used to simulate the temperature-field of the quenched sample.The simulated result is consisted with the measured one.（2）The hardenability curves of the 7050-T6 samples are determined by spraying water,10-wt%brine and PAG regent at 20℃,respectively, the depths corresponding to HV3=175（hardness approximately decrease by 10%）are 60mm,60mm,45mm,respectively.The most stable hardenability curve is contributed by spraying PAG reagent.（3）The precipitation of.（MgZn2）phase,remotion of grain or/and subgrain boundaries,and precipitation free zone（PFZ）are affected by the cooling rates.The critical average cooling rate of precipitating phase is about 40～60℃/S.

Related Dissertations

  1. Reactive Hot-Pressing and Mechanical Properties of （ZrB2-ZrO2）/BN Composites,TB332
  2. Microstructure and Mechanical Properties of Mg-Zn-Y-Zr Alloys,TG146.22
  3. Investigation on Microstructure and Properties of Cadmium-Free Silver-Based Intermediate Temperature Filler Metals,TG425.2
  4. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  5. The Investigations on the Characteristics and Mechanism of NIR Emission from Bi-doped Silicophosphate Glasses,TQ171.1
  6. Preliminary Study on Salt-Tolerant Mechanism of the New Pennisetum Purpereum Schumach Variety-Sumu No.2,S543.9
  7. Study on the Fine Structure of Intestine and Intestinal Mucosal Barrier in Zebrfish (Brachydanio Rerio),Q95-33
  8. Study on Characteristics of Morphology Anatomy and Physio-Biochemistry of Two Ecotype Varieties Cucumber Leggy Seedilings,S642.2
  9. Study on the Mechanism of Heat-Induced Gelation of Myofibrillar Proteins,TS251.1
  10. Studies on the Aggregation and Microstructure of Imidazolium Ionic Liquids in Solutions,O645.1
  11. Studies of Luminescence Characteristics of Eu3+-doped Rare Earth Borates REBaB9O16 （RE=rare Earth Ions and Y）,O627.3
  12. The Research on Extrusion Parameters Through the Plate Billet of Magnesium Alloy,TG379
  13. Study on Microstructure and Superconducting Properties of MgB2 Wires Fabricated by Two-Step PIT,TM26
  14. Study on Morphological Evolution and Toughening Mechanism of Sandbag Microstructure-toughened PA6/EPDM-M/nano-CaCO3 Ternary Composites,TB33
  15. The Photoluminescence of H1.77 [Sr0.8 Bi0.21Ta2 O7] Nano-layers Annealing under Different Temperatures and the Effect of the Cu2O Addition on Its Photocatalytic Activity,O482.31
  16. Compressive Strengthes and Microstructural Characteristics of Fiber Reinforced Geopolymer,TB321
  17. Study on Influence of Preferred Orientation on Mechanical and Recoverable Properties of TN479 Shape Memory Alloy Sheet,TG139.6
  18. Numerical Simulation and Research of Plate in the Process of Roller Quenching,TG156.3
  19. Research of H-beam Steel after Ultra Fast Cooling,TG335.4
  20. Study on DC Casting of Aluminum Alloy under the Dual-frequency Electromagnetic Fields,TG292
  21. Low-Frequency Magnetic Pulsing Effect as Well as EET Study of Amorphous Alloy Fe43Co43Hf7B6Cu1,TG139.8

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > Heat treatment > The heat treatment of non-ferrous metals and their alloys > The heat treatment of aluminum and its alloys
© 2012 www.DissertationTopic.Net  Mobile