Dissertation > Excellent graduate degree dissertation topics show

Fabrication of TiAl Based Alloy by Powder Metallurgy and Study on Property

Author: ZhangGuoLiang
Tutor: HuLianXi
School: Harbin Institute of Technology
Course: Materials Processing Engineering
Keywords: TiAl based alloy reactive sintering hot hydrostatic extrusion mechanical property
CLC: TF125.2
Type: Master's thesis
Year: 2007
Downloads: 428
Quote: 2
Read: Download Dissertation

Abstract


TiAl based alloys are widely studied because their light weight and excellent elevated temperature properties such as high strength retention, resistance to creep and oxidation. However, their application is currently limited by the poor ductility and strong resistance to deformation at elevated temperature. In addition, it is difficult to prepare TiAl alloy with fine and homogeneous microstructure by traditional casting and mechanical working processes. Therefore, a new technology, which consists of the mechanical blending, reactive sintering and hot hydrostatic extrusion, has been put forward.The material of the experiment is the mixture of Ti and Al elemental powders prepared by mechanical blending for 72 hours and than consolidating into densified billets. The powder billets need reactive sintering at low temperature and high temperature, in order to get high densified TiAl alloy. And then hot hydrostatic extrusion is used to press the sintered billets. By high-temperature compression test of the obtained samples, the mechanical properties of TiAl based alloy were investigated. The following aspects have been researched on.Low temperature reactive sintering was studied. The expansion during the vacuum reactive sintering at low temperature of the powder billets was experimentally investigated, and the reasons of expansion were theoretically analyzed. The method of low temperature reactive sintering was generalized, and the experiment testified the method effective.The following aspects were accomplished after high temperature reactive sintering. The rule of the shrinkage of the billets was generalized from the result of density of the billets, which have been reactive sintering at high temperature. By X-Ray analysis of the obtained samples the degree of the reaction was researched when the temperature and time changed. At last the regularity of the metallurgical structure of TiAl alloy was investigated, when the high temperature and time changed.The following aspects were accomplished after hot hydrostatic extrusion. The density of the billets got bigger after hot hydrostatic extrusion. By high- temperature compression test of the obtained samples, the mechanical properties of TiAl based alloy were investigated. The influence of testing temperature on the compressive yield strength of as-sintered alloy has been made clear.

Related Dissertations

  1. Study on the Mg-Si Alloys Prepared with the Fine Si Powders as the Raw Material,TG339
  2. Microstructure and Property of Friction Stir Welding Jiont for High Strength Aluminumalloy Under Controlled Cooling Condition,TG407
  3. The Thermal Stability of Refractory-metals Containing γ-TiAl Based Alloys Subjected to a Long-term Exposure 700℃ in Air,TG146.23
  4. Investigation of High Temperature Deformation Behaviors and Microstructure Mechanical Properties of High Nb Containing TiAl Allly with MO,TG132.32
  5. Study on Hot Deformation Behavior and Processing Map of Ti-46Al-2Cr-4Nb-0.3Y Alloy,TG146.23
  6. Study on Tial Based Alloy Coating Treated by Plasma Nb-C Alloying and Its Theoeretical Study of Diffusion Mechanisms,TG178
  7. Research on High Temperature Comprassion Behaviors of Ti45Al5Nb0.8Mo0.3Y Alloy,TG146.2
  8. The Preparation and Properties of SiC/B4C Composite Ceramics by Reactive Sintering,TQ174.1
  9. Research on Plasma Surface Cr-Si Alloying and the Tribological Behavior of Tial-based Alloy,TG174.4
  10. Effect of ECAP on Microstructure and Mechanical Properties of Solid-State Recycled AZ91 Chips,TG146.22
  11. After rolling of high - quality hard-wired control microstructural evolution and mechanical properties of cold process,TG142.1
  12. The Microstructures and Properties of SiC_p/Al Matrix Composites Prepared by Reciprocating Extrusion,TB333
  13. Study on the Synthesis and Properties of Copolyimides Derived from ODPA/Isomeric ODA,TQ323.7
  14. Preparation and Properties of PVA Based Gel with γ Irradiation as Repairing Material for Articular Cartilage,R318.08
  15. Study on the Effect of Performances of Cu-Ag Alloy by ECAP,TG376
  16. Development of Alumina Based Nanocomposite and the Application in Tool and Die,TB383.1
  17. The Study of Space Polymers/nano-Silica Sol Hybrid Materials,TB383.1
  18. The Mechanical Properties and Corrosion Resistence of AlN-SiC Ceramic Composites,TQ174.1
  19. Structure Design and Synthesis of High Properties ABS Resin,TQ325.2
  20. The Study on High Flowing PVC Based Alloy by Injection Moulding,TQ325.3
  21. Research on Microstructure and Mechanical property of 4032 Aluminum Alloy Scroll,TG319

CLC: > Industrial Technology > Metallurgical Industry > Metallurgical Technology > Powder metallurgy (metal ceramic technology ) > Powder metallurgy products and their applications > Non-ferrous metal products
© 2012 www.DissertationTopic.Net  Mobile