Dissertation > Excellent graduate degree dissertation topics show

Study of the Materials of Piece Type Limiting Current Oxygen Sensor with Dense Diffusion Barrier

Author: WuBangJun
Tutor: ZengYiKe
School: Huazhong University of Science and Technology
Course: Materials Physics and Chemistry
Keywords: oxygen sensors dense diffusion barrier solid electrolyte doping ZrO2
CLC: TP212
Type: Master's thesis
Year: 2007
Downloads: 156
Quote: 0
Read: Download Dissertation

Abstract


With the development of the technology for automobile and manufacture craft of sensors, automobile oxygen sensors are consummating constantly with a wide developing foreground. To overcome the disadvantage of the traditional current type oxygen sensor and optimize the testing performances of sensor, using solid state electronic-ion mixed conductor as the material of the preparation of limiting current oxygen sensor with a dense diffusion barrier is studied in this article. This kind of oxygen sensor has a better oxygen sensitive characteristic then broadened a sensor measures range. It has many merits such as inexpensive, simple structure, respond quickly and work reliable. So it is the one kind of the limiting current oxygen sensor which has a good prospect.In this thesis, a new gel-casting method has been studied: mix the Y2O3 stabilized ZrO2 powder body with organic monomer, coupler, dispersant and the plasticizing agent according to a certain proportion. Then pour the slurry into a model after drop little initiator and accelerating agent in it. Then it has prepared the materials of each part in the oxygen sensor, carried on the material modification and analyzed the results.Electrolyte material: prepared the Y2O3 stabilized ZrO2 ceramics by a new gel-casting method. YSZ sintered at 1400℃has became the cubic fluorite structure, and sintered at 1500℃whose relative density can reach 95.1%, using gel-casting method can reduce the sinter temperature by 100～200℃. The samples which mixed with Al2O3 have lower rate of contraction, higher volume density, and good sintering character.Dense diffusion barrier material: the best sintering temperature of La0.8Sr0.2MnO3 material is determined 1000℃, synthetic reaction can finish at this temperature. The samples sintered at 1200℃whose relative density can reach 97%. As increasing of strontium in La1-xSrxMnO3, the volume density of the samples decrease and the sintering character descend.Conductive ceramics material: the electrical resistivity of ZnO ceramic will decrease slowly when increasing of the Al2O3, and the electrical resistivity reaches the least when the quality percent of Al2O3 is 0.5%; and the electrical resistivity descend quickly when the sintering temperature raise up. The electrical resistivity of ZnO conductive ceramic mixed with Y2O3 sintered at 1000℃is the biggest which reaches 220Ω·cm . And the electrical resistivity descend when the sintering temperature raise up. When the sintering temperature between 1000℃and 1200℃, the electrical resistivities of the ZnO samples fall over 90%.

Related Dissertations

  1. Reactive Hot-Pressing and Mechanical Properties of （ZrB2-ZrO2）/BN Composites,TB332
  2. Preparation of One-dimensional Nano TiO2 and Study on the Decolorization of Dyeing Wastewater,TB383.1
  3. First-Principles Studies of Cathode Material LiMO2 （M=Co, Ni, Mn） of Lithium Ion Batteries,TM912
  4. First-Principle Studies of Cathode Materials LiFePO4 and Its Doped Systems for Lithium Ion Batteries,TM912
  5. Synthesis and Electrochemical Performances of New Lithium-ion Battery Cathode Materials Li3V2（PO4 ）3 and Li[NixLi1/3-2x/3 Mn 2/3-x/3)O2,TM912
  6. Effect of Adding ZrO 2 Nanopowder on Microstructure and Mechanical Properties of Carbon Steel,TB383.1
  7. Studies of High Refractive Index Materials Prepared by Nano ZrO2 and TiO2 Hybrid Silicone Epoxy Resin,TB383.1
  8. The Affect of Microstructure and Properties Adding ZrO_ 2 Nanoparticles on Carbon Steel,TG142.31
  9. Preperation of Low Friction and Wear Resistant High-Purity Alumina Ceramic,TQ174.1
  10. Preparation and Properties of ZnO-based Diluted Magnetic Semiconductors,TN304.21
  11. Studies on Catalysts for Hydrogen Production from Low Temperature Steam Reforming of Dimethyl Ether,TQ426.94
  12. Synthesis and Modification of Nano LiFePO4 as Cathode Materials,TM912
  13. Precursor Preparation of ZrO 2 -modified C / SiC composite materials and their properties,TB332
  14. Preparation and Physical Properties of Mn and Co-doped SiC Diluted Magnetic Semiconductor Films,TN304.055
  15. Material Structure Design and Fabrication Technique of GaN Ultraviolet Photocathode,TN23
  16. Study on Two Dimensional Ultrasonic Vibration Grinding Temperature Field Distribution Character of Nano ZrO2 Ceramics,TG580.6
  17. Tribological Properties and Corrosion Resistance to Molten Steel of （ZrB2-ZrO2）/BN Composites,TB332
  18. Preparation of Cu-Ce-Zr Composite Oxide Nano-particulates by SAS Process and the Controllable Synthesis of Hollow Structure,TB383.1
  19. Preparation and Characterization of Ion-doped Type and Oxide or Noble-metal Supported Type TiO2 Nano-wire（belt）,TB383.1
  20. Preparation of solid catalyst biodiesel and its application,TE667
  21. Preparation of Zirconia-based Dental Bioceramics and Measurement of Its Mechanical Performance,TQ174.75

CLC: > Industrial Technology > Automation technology,computer technology > Automation technology and equipment > Automation components,parts > Transmitter ( converter),the sensor
© 2012 www.DissertationTopic.Net  Mobile