Dissertation > Excellent graduate degree dissertation topics show

An Analysis on Meshing Performance of Offset Cylindrical Worm Gearing and a Study on Worm Processing

Author: YueQin
Tutor: SunYueHai
School: Tianjin University
Course: Mechanical Design and Theory
Keywords: offset cylindrical worm gearing contact line involute helical gear meshing performance disc cutter
CLC: TH132.44
Type: Master's thesis
Year: 2010
Downloads: 25
Quote: 2
Read: Download Dissertation

Abstract


Offset involute cylindrical worm gears is a composition of the transmission by the worm and worm wheel meshing, which is characteristic of small size ,big transmission ratio, low vibration and noise. This paper mainly studies on the worm which is a involute helical gear with few teeth in substance orthogonal to the face gear (ie worm gear). The meshing performance,optimization of parameters of the second quadrant of the offset involute cylindrical worm gearing and the screw worm tool’s design is the primary concern. The content of this research is as follows:Firstly, based on the theories of the differential geometry and gear meshing, mathematical model of the second quadrant of the involute offset cylindrical worm gearing drive is established by kinematics method. Derived function of the worm meshing, meshing equation, worm wheel’s tooth surface equations and the boundary line equation of worm screw gear tooth surface are also deduced.Secondly, according to the theoretical equations of the second quadrant offset involute cylindrical worm gearing drive, in the light of their mathematical model, the meshing of its performance is simulated. The influence of design parameters on involute offset cylindrical worm gearing drive is emphasized. Analysis showed that an appropriate increasement in helix angle, increasement in modulus, reduction in worm gear teeth, reduction in the number of worm head , increasement in the heliciod working length of worm gear can improve the distribution of contact line, which can make the transmission performance better.The last, the research in processing the well-established involute helicoid worm tooth has been done. The use of profiling method of processing principle and the use of contact line method turn out contact conditions between a disc cutter and the workpiece surface spiral surface. The disc cutter axial truncated map is designed by programming software. At the same time, the deflection of disc cutter axial truncated map is also studied, which is caused by the modified gear.

Related Dissertations

  1. Shield the typical cutter combination rock breaking force characteristics,U455.3
  2. Studying on Cutting Tool Replacing Cycle of the TB880E Tunnel Boring Machine,U455.31
  3. Load Spectrum Complication of Disc Cutter of Full Face Rock Tunnel Boring Machine,U455.3
  4. The Development of Double Discgrass Cutter,S817.111
  5. Performance Analysis of MC Nylon Helical Gear Based on the Finite Element Method,TH132.41
  6. Design and Study on Disc Cutter of Ramie,S225.913
  7. Study on Low Cycle Fatigue Properties of Copper Alloy Contact Wire,U225.41
  8. Study and Optimization of Parameter on Cutting Tools for Engine Manufacturing,U468.21
  9. TBM disc cutter rock crushing characteristics and under the action of the vibration characteristics of the hob,U455.3
  10. Study of Crossed Helical Gears Meshing Performance,TH132.41
  11. Design of the Fully Wiped Co-rotating Twin Screw’s Tooth Profile and Study on Method for Machining the Twin Screw,TG62
  12. Cutter Layout Design of Full-face Rock Tunnel Boring Machine,U455.3
  13. Study on Daily Inter-regional Tie-line Generation Schedule Management System in Northeast China Power Grid,F426.61
  14. The Over-Voltage Analysis of Separation between Pantograph and Overhead Contact-Line,U264.34
  15. TBM disc cutter vertical force and lateral force prediction model,U455.3
  16. Research of the Oscillation Mode of the Interconnected Power Grid,TM712
  17. Study on the Hourglass Worm Driving with Circular Helicoid Generatrix,TH132.44
  18. Twisted lobe rotor Roots blower design , simulation and manufacturing,TH444
  19. Study of Medium Voltage Distribution Network Planning,TM715
  20. 3D Measurement System Technology Research for Free Curve Plan Based on Structured Light Measurement Principle,TP274.4

CLC: > Industrial Technology > Machinery and Instrument Industry > Mechanical parts and gear > The transmission mechanism > Meshing > Worm gear
© 2012 www.DissertationTopic.Net  Mobile