Dissertation > Excellent graduate degree dissertation topics show

Study on Preparation Technology by Thermodynamics and Performance of Iron-Based Powder Metallurgical Material Containing Nitrogen

Author: NingWenTao
Tutor: YangChuan
School: Southwest Jiaotong University
Course: Materials Science
Keywords: Fe-based powder metallurgy material containing nitrogen preparation technology performance study thermodynamics kinetics
CLC: TF124
Type: Master's thesis
Year: 2008
Downloads: 57
Quote: 1
Read: Download Dissertation

Abstract


Iron nitride has high hardness and good wear resistance,corrosion resistance and magnetic properties.If we replaced iron-base powder metallurgical material with Fe-based powder metallurgy material containing nitrogen,some performance defects of iron-base powder metallurgical material can be improved,so that the lifetime of material shall be extended and the economic benefits shall be improved.The thesis focuses on the preparation technology and performance of Fe-based powder metallurgy material containing nitrogen.The Fe-based powder metallurgy material containing nitrogen was prepared using Fe3N powder by means of cold isostatic pressing and sintering in a protective atmosphere which was formed by mingling proportional H2 with N2.And Fe3N powder was prepared using nitrified reduced ferric oxide powder but iron powder.The thesis studied on the component,structure,physics and mechanics performance of the Fe-based powder metallurgy material containing nitrogen,and analyzed the process of powder-making and sintering in accordance with diffusion kinetics and thermodynamics.The results show that the Fe-based powder metallurgy material containing nitrogen is composed of Fe and Fe4N,and the content of Fe4N is 19%.The material has high density, the electric resistivity is 19μΩ·cm,the saturation magnetization is 86.8emu/g and the coercive forces and remanence are 26Oe and 0.45emu/g respectively.By comparing with the conventional Fe-based powder metallurgy material,the hardness,corrosion-resistance and wearing resistance of the nitride powder metallurgical material are improved by 2～3 times,2～3 times and 1～2 times.The results of thermodynamics show that the nitrified reduced ferric oxide powder is better than iron powder.Fe4N can also be oxidized under low oxygen partial pressure,so there must be protective atmosphere in the process of sintering.It explains nitrogen potential and the diffusion mechanism of nitrogen atom with sintering kinetics.The sintered materials with plentiful Fe4N could be prepared by sintering in NH3-N2 atmosphere.During the sintering process,NH3 supplied the nitrogen potential and N2 reduced the hydrogen partial pressure,so that the nitrogen potential could be controlled.

Related Dissertations

  1. Study on the Degradation of Unsaturated Polyester Resin and Fiber Reinforced Polymer in Hot Compressed Water,TQ320.1
  2. Quantitative Analysis of Pyrolysis Component of Typical Low Volatile Coal of Chinese,TQ530.2
  3. Process Optimization and Degradation Kinetics for Microwave Vacuum Drying of Different Traditional Chinese Medicine Extract,TQ461
  4. Characterization and mechanism of the titanium dioxide surface envelope,TQ621.12
  5. Hot air drying characteristics of lettuce osmotic dehydration mass transfer kinetics and permeability,TS255.52
  6. Improvement of Preparation Technology for Chitin and Chitosan from By-product of Litopenaeus Vannamei,TS254.9
  7. Adsorption Effects of Phosphate and Chromium from Aqueous Solution by Adsorption Using LDH and Mg/Fe/Al Modified Montmorillonites,X703
  8. Study on the Preparation Technology and Quality Standard of Danggui Dropping Pills,TQ461
  9. Polycyclic aromatic hydrocarbons degradation of the growth characteristics of bacteria in soil remediation,X172
  10. Protective Effects of Soy Saponins on Acute Alcohol-induced Liver Damage,R285.5
  11. Research on Adsorption Mechanism of Bromine from Concentrated Seawater by D201 Resin and Analytical Methods of Bromine,TQ124.51
  12. The Effect of Change of Hamstring and Quadriceps Femoris Strength of Knee on Continuous Vertical Jump,G804.2
  13. Formation of Biogenic Manganese Oxide and Oxidative Degradation of Environmental Representative Enstrogens,X703
  14. Study on the Adsorption of Aqueous Phthalate Ester (Dibutyl Phthalate) on Bamboo-Derived Biochar,X703
  15. Study on Preparation and Dyeing Technology of PANI/PET Composite Fabric,TS193
  16. Catalytic Degradation of AO7 in the CeO2/H2O2 System,TB383.1
  17. Research on Reaction and Process for Catalytic Dehygrogenation of Iminodibenzyl to Iminostilbene in Gas-phase,TQ463.2
  18. Study of the Preparation and Adsorption Properties of the Ion-Exchange Resin-Based Spherical Activated Carbon,TQ424.1
  19. Catalytic Hydrogenation of P-Phenylenediamine to Prepare Diaminocyclohexane over Raney-Ni,TQ236
  20. The Modification of Attapulgite Clay and the Application in Dyeing and Printing Wastewater Decoloring,X791
  21. Endogenous iron-based composites and tribology research,TB331

CLC: > Industrial Technology > Metallurgical Industry > Metallurgical Technology > Powder metallurgy (metal ceramic technology ) > Powder molding, sintering and post-processing
© 2012 www.DissertationTopic.Net  Mobile