Dissertation > Excellent graduate degree dissertation topics show

Research on Interface Properties of Composite Seal Material Composed with Metal and Fluorine Rubber

Author: LiuHui
Tutor: ZhangAiLing
School: Shenyang University of Technology
Course: Applied Chemistry
Keywords: Fluorine rubber Adhesive Composite materials Interface properties LCD epoxy resin
CLC: TQ333.93
Type: Master's thesis
Year: 2010
Downloads: 81
Quote: 0
Read: Download Dissertation

Abstract


Fluorine rubber has the excellent heat resistance, oil resistance, weather resistant, ozone resistant and chemical resistance character.Because of these Superior performance,people often use this kind of materials in the area of the automobile and aerospace and so on.In the actual application,people often make the composite material composed with fluorinerubber and metal, improving the tightness of the composite material. But because of the small fluorine rubber and bad reaction dot, there have some difficulties in adhesiving fluorine rubber and metal. cementation exist great difficulties. It also has the poor mechanical properties and medium resistance, therefore, the choice of appropriate adhesive for fluorine rubber and metal cementation play an important to improve the composite seal material interface properties.This paper is aim to synthesize three types of epoxy adhesive. Bisphenol A epoxy resin is synthesized under the 80℃in 4h,and the mole ratio of bisphenol A to epichlorohydrin is 1:5, in 10mol/L sodium hydroxide,getting the light brown transparent liquid, yield is 74.88%, and has the same IR as the standard authentication. LCD epoxy resin is synthesized under the 90℃in 4h,and the mole ratio of 4,4’-dihydroxy-a, a’-dimethyl benzalazine(DDBA) to epichlorohydrin is 1:15, in 10mol/L sodium hydroxide adding with benzyltrimethylammonium hydroxide, getting the yellow solid, yield is 67.45%. Polarizing microscope and DSC proved its LCD performance,its kind is nematic liquid crystal,and the dielectric crystalling phase range is from 114.48℃to 164.43℃.The metal-fluorine rubber composite sealing material is respectively adhesived by the above two kinds of adhesive and modification aramid enhance epoxy.The metal is the 301 stainless steel plate material. Medium resistance and adhesive performance tests result shows that the Composite seal material useing LCD epoxy resin as adhesive has the best performance.The technological conditions is as fllows:the quality ratio of epoxy resin to fluorine rubber is 1:10, the addition of LCD epoxy resin into normal epoxy resin is 4%, under the cure temperature of 180℃for 1h. Composite sealing material do not change in the glycol solution for 5 hours, the quality change ratio is 0.22%. It neither fall off nor peeling under the high temperature 200℃for 5h, the quality change ratio is 0.21%.The oil resistance test find that composite material surface do not have opparent change, the quality change ratio is 0.23%. The adhesion tests shows that the grade for the composite material 1 grade. The tension performance test also have the good performance,its strength comes to 7.39 MPa.

Related Dissertations

  1. Preparation and Characteration of Composite Microspheres with Dual-, Triple- Responsive Properties,O631.3
  2. Multiscale Analysis for Layered Composite Materials and Anisotropic Finite Element Method,O241.8
  3. β-SiAlON/Al_2O_3 composite powder and its combination of β-SiAlON spinel composite,TB332
  4. The Investigation of Bone Marrow-derived Dendritic Cell by Atomic Force Microscopy,R392
  5. The Technical and Economic Feasibility Analysis of J-D Aluminum-plastic Composite and Resistant Cooking Adhesive Achievements,F426.72
  6. Fabrication of Locally Reinforced Manganese Steel Matrix Composite and Study on Stability of Low Temperature Martensite,TB331
  7. Fabrication and Properties of a ZnO Reinforced Cu-Matrix Composite,TB331
  8. Preparation and Properties of Graphene and Graphene-based Nanocomposite,TB383.1
  9. Preparation of Thermal Energy Storage Composite Materials and Study on Dynamic Performances of Thermal Storage Systems with Heat Pipe,TB33
  10. Optimum Design of Handing Composite Chimney Based on the Genetic Algorithm,TU233
  11. Study on Amphiphilic Hot-melt Pressure Sensitive Adhesives for Transdermal Drug Delivery of Chinese Medicine,TQ436.3
  12. Reserch of Nickel Plating Carbon Nanotubes and CNTs/SiCp/Mg Composites Material,TB383.1
  13. Application on the Use of Paraffin in the Field of Phase Changes Textiles,TB34
  14. Experimental Study on Mineralization of Hydroxyapatite Crystals Induced by Phosphate Dentin Adhesive,R783.1
  15. On the Social Identity of "Phoenix Man",F224
  16. Study on the Nano-Fe3O4/NR Composites,TB332
  17. Heat and Mass Transfer Hot-pressing Model of Medium Density Fiberboard,TS653.6
  18. Composite flywheel for energy storage structural mechanics and energy storage research,TH133.7
  19. Preparation and Properties of Thermal Adhesive of Nano-BN as Addttive,TB383.1
  20. Delamination Simulation of Laminated Plates Based on A Progressive Damage Model,TB33

CLC: > Industrial Technology > Chemical Industry > Rubber Industry > Synthetic rubber > Fluorine rubber, silicone rubber
© 2012 www.DissertationTopic.Net  Mobile