Dissertation > Excellent graduate degree dissertation topics show

Application Research of Manufactured Sand and Concrete

Author: SunYongTao
Tutor: QiuYanJun
School: Southwest Jiaotong University
Course: Road and Railway Engineering
Keywords: manufactured sand mix design grain composition mechanical property endurance quality
CLC: TU528
Type: Master's thesis
Year: 2010
Downloads: 148
Quote: 1
Read: Download Dissertation

Abstract


As the significant programming planed by the Ministry of Communication that to fulfill the whole of expressway system with a mileage of 4.3 till 2020 and the practice of western development are in progress, nowadays the exploitation and supply of construction material of our country have both been under pressure. Along the Naqian Freeway, there is lack of natural sand and thereby a lot of building sand must be transported from other places that are far away from the construction site. However building stones, especially limestone, are abundant along the Naqian Freeway. So efforts to turn building stones into manufactured sand and then to cut down project cost_are undoubtedly necessary.Being a part of Researches on The Key Constructive Technique of Naqian Freeway in Karst Regions, which are carried out by the transportation department of Sichuan province, this paper aims at knowing the mechanical property as well as the endurance quality of concrete C50 that contains manufactured sand. In this way, whether manufactured sand can be used in the construction of Naqian Freeway and how effective it will be will finally get uncovered.Here are some main achievements of this paper:(1). Conclusions of popular overseas and domestic producing technique of manufactured sand; On-the-spot investigations of aggregate preparation methods performed in contract sections of Naqian Freeway; Analysis of the basic property of manufactured sand produced in the contract sections being investigated and suggestions for technique improvement and better engineering application.(2). Mix designs of concrete C50 and researches on influence factors of the performance of concrete used inengineering practice, such as water-cement ratio, sand ratio, mineral blend composition, rock powder, grain composition and etc.(3). Systematic experiments and researches on the endurance quality of concrete C50; Elaborate analysis of its long-term strength, impermeability, ability to work against circular freezing and thawing, anti-carbonization ability, while applying natural sand, manufactured sand and hybrid sand respectively; Systematic studies of the principles that how the rock powder content influences the endurance quality of concrete C50 consists of manufactured sand and other components.

Related Dissertations

  1. Study on the Synthesis and Properties of Copolyimides Derived from ODPA/Isomeric ODA,TQ323.7
  2. Properties on Aramid 1313 Fabric and the Compound Silastic Rubber Composite Material with This Fabric,TB332
  3. Properties and Ultrasonic Grinding Experimental Study on the Nano Ceramics Toughened by ZrO2,TG580.6
  4. Study on the Mg-Si Alloys Prepared with the Fine Si Powders as the Raw Material,TG339
  5. Research on Preparation and Properties of Ti(c,n)/nicr-based Cermets,TG148
  6. Microstructure and Property of Friction Stir Welding Jiont for High Strength Aluminumalloy Under Controlled Cooling Condition,TG407
  7. A Study of Mechanical Properties of Proton Exchange Membrane,TM911.4
  8. Mechanical Property Analysis on Working Equipment of Hydraulic Excavator,TU621
  9. Research of Crumb Rubber Modified Cement Concrete Pavement Performance,U414
  10. Studies on Strain Rate Dependence of Mechanical Behavior of Amorphouis Polymer,O341
  11. Study on the Self-bonding Property of Non-wood Plant-based Particles/Powders,TS653
  12. The Study of 6082 Al-Mg-Si Alloy Joints’ Mechanical Properties and Microstructure by Ar Arc Welding,TG407
  13. Studyon Microstructureand Property of Aluminum(Magnesium)Alloyvia Lost Foam Casting by Vibration Solidification,TG249.6
  14. First-Principles Study on the Properties of δ and γ" Phases and the Recrystallization Behavior of Cold Rolled INCONEL 718 Super-Alloy,TG111.7
  15. Effect of RE Element Nd on Microstructure and Mechanism Properties of Hyper-eutectic Aluminum Silicon Alloys,TG294
  16. Study on Hot Rolling Process of AZ61 Magnesium Alloy,TG339
  17. Study on Microstructure and Mechnical Properties of Ti_f/Al Composites,TB331
  18. The Study on Fabrication of SiC_p Reinforced Magnesium Composites by Powder Extrusion Technology,TB331
  19. The Study on the Microstructure and Properties of 3D-Meshy SiC/Cu Composite Material,TB333
  20. Mechanical Property Study of Open Spandrel Bonded Prestressed Steel Reinforced Concrete Beam,TU398.9

CLC: > Industrial Technology > Building Science > Building Materials > Non-metallic materials > Concrete and concrete products
© 2012 www.DissertationTopic.Net  Mobile