Dissertation > Excellent graduate degree dissertation topics show

Marine Boiler Superheater Tubes Expansion Port Stress and Strain Analysis

Author: MaYi
Tutor: SongFuYuan
School: Harbin Engineering University
Course: Thermal Power Engineering
Keywords: superheater expansion joint FEM expansion port leakage
CLC: TQ051.5
Type: Master's thesis
Year: 2011
Downloads: 4
Quote: 0
Read: Download Dissertation

Abstract


The steam superheater is one of the most important components of marine boiler. It holds the extremely important status in the entire steam power installment. The function of superheater is further heating the saturated steam generated in the drum to a higher temperature of superheated steam to meet the needs of marine navigation. The tubes of the superheater and the headers’ tube sheet are usually connected by expansion. Sometimes the expansion port of the superheater is finding to be leaky during the operation process.This thesis focused on the study on the causes of expansion port leakage. The main content of this study were as follows:1. On the basis of consulting of plenty of literatures about tube-to-tubesheet joint, using ANSYS finite element analysis software, after appropriate simplification, the 3-D finite element model of marine boiler superheater tube-to-tubesheet joint is established. By using elastic-to-plastic finite element analysis of the process of expansion joints,12Cr1MoVg, 1Cr19Ni11Nb, GH984 these three common materials of superheater tubes’expansion performance to the header box were studied. The results of analysis indicated:the three materials all have good cold expansion performance, grooving on the tubesheet has benefit to the expansion joint, two grooves on the tubesheet can make the joint get better expansion performance.2. Analysis the seal performance of the expansion joint when it is in the high temperature working state. The results indicate:when using 1Cr19Ni11Nb as superheater tubes, the joint can keep in touch and seal. It will leak in the cooling process.Exert temperature and pressure cyclic loads on the joint, then analysis the load cycle number on the impact of sealing performence of joint. The results indicate:with the increase of the load cycle number, the residual contact pressure in the joint decreased slightly in the cooling process. This thesis also inspected high temperature on the impact of sealing performance of the joint, when using 12Cr1MoVg and GH984 as the tube. FEA results show that the higher the working temperature is, the lower the residual contact pressure is after from the high temperature state to the room temperature. 3. The residual contact pressure of the joint decrease after start and shutdown the boiler, and expansion leakage. This mainly caused by the difference of coefficient of thermal expansion between tube and tubesheet. This thesis discussed the cases that tube and tubesheet have different coefficient of thermal expansion. It finds that when the tube’s coefficient of thermal expansion is higher than the tubesheet’s, the joint will leak during the cooling process. When the tube’s coefficient of thermal expansion is lower than the tubesheet’s, the joint will leak during the heating process.Through the above theoretical reseach, it gives some advice to avoid expansion port leak, and has some significance for application.

Related Dissertations

  1. Analysis of Flexspline Stress and Tooth Wear in Harmonic Gear Drive,TH132.43
  2. The Effect of Current Density and Electric Field on Ni and Its Alloy Electrodeposition for Copper Crystallizer,TQ153.2
  3. Finite Element Analysis and Optimization Design of a Tractor Cab,S219.02
  4. Steering Mechanism and Hydraulic System for the Electronic Control Hydraulic Power Steering System of Tractor,S219.02
  5. TWIN BLOCK appliance reconstruction when combined in different stomatognathic muscles and ligaments associated constraint force of impact,R783.5
  6. Undersea robot plow trenching machine design and analysis,TE952
  7. Study on Shear Bearing Capacity of HRBF500-Reinforced Concrete Beams,TU375.1
  8. The Surrounding Rock Monitoring and Finite Element Simulation of Subway Tunnel,U455.43
  9. Reliability-based Sensitivity Research on Multi-span Rotor System,TH113
  10. Study on Stamping-forging Process and Experiment of Sheet Metal Parts with Non-uniform Thickness,TG386
  11. Study on the Influence of Various Defects on the Characteristics of Infrared Photonic Crystal Fiber,TN253
  12. Hot stamping door impact beams Experimental studies and material properties gradient optimization,U467.3
  13. Tipper Lifting Mechanism and the sub-frame structural analysis and optimization,U469.4
  14. 9F gas turbine exhaust system architecture design and analysis,TK473
  15. Passive microfluidic channel mixer topology optimization,TH703
  16. The mechanical properties of fiber reinforced concrete research and finite element analysis,TU528.572
  17. Direct-drive A / C -axis CNC universal milling head swivel double Finite Element Analysis,TG547
  18. Oil-immersed transformer temperature field numerical calculation and analysis,TM411
  19. Converter transformer winding end analysis and optimization of the electric field,TM42
  20. Dry-type air-core reactor temperature field loss and,TM478

CLC: > Industrial Technology > Chemical Industry > General issues > Chemical machinery and apparatus, equipment > Chemical process machinery and equipment > Heating, cooling machinery
© 2012 www.DissertationTopic.Net  Mobile