Dissertation > Excellent graduate degree dissertation topics show

Analogue of Plastic Mould Steel during Laser Strengthening

Author: WangZhenHua
Tutor: JieXiaoHua
School: Guangdong University of Technology
Course: Materials Processing Engineering
Keywords: Laser Transformation Hardening Temperature field Stress field Analogue Wear
CLC: TG142.15
Type: Master's thesis
Year: 2008
Downloads: 99
Quote: 0
Read: Download Dissertation

Abstract


The author has made some analogue experimental researches on laser transformation hardening.Transformation hardening on 718、738 plastic mould steel’s surface with YAG laser was investigated,Analyzed the temperature field coursed by laser radiate on 718、738 plastic mould steels with the software of finite element、analyzed the transient stress field coursed by temperature field of 718,738 steels under laser libeling.Obtained the transient temperature and stress distribution,when the steel is under load.The results indicate that when the laser power and facula diameter are invariableness,heat affecting inside the work-piece produced by surface moving thermal source along moving direction doesn’t change as the position changing.The thermal hysteresis phenomenon from inside to outside existed while laser processing.Center of the highest temperature is behind the facula.The temperature gradient in front of the facula is lower,but behind the facula temperature gradient become ciiffed.Temperature field distribution is from unsteady state to quasi-stable state;Compressing stress developed inside the facula when scanning.And the stress is overhanging along scanning direction;outside the facula,compressing stress is reducing and tension stress is increasing continuously as the distance increasing.This test do some researches on how do the different scan speed affect the depth and width of the hardened layer,hardness,and resist wear performance, the hardened layer is obtained by the technology called laser transformation hardening.The results indicate that when the laser power and facula diameter are invariableness,with the increment of scan speed,the hardness increases at the first moment and then decrease;The hardness of the layer reaches 700HV above, and is 1.5 times than the base metal’s.The hardness layers are about 0.3mm-0.5mm thickness,and 0.3mm-0.5mm width.The sliding abrasion properties of the layer were tested.The result shows the layer friction coefficient is much smaller than that of the sample without hardening.The resist wear performance is fine,the layer friction coefficient is small;This test also do some researches on resist wear performance。The results indicate thatwhen the laser power and facula diameter are invariableness,as the increment of scan speed,wearing weight loss increases at the first moment and then decrease.The surface morphology of the layer were observed by Scan Electron Microscope(SEM).The abrasion morphology shows that abrasion mechanism is mostly grain abrasion.

Related Dissertations

  1. Reactive Hot-Pressing and Mechanical Properties of （ZrB2-ZrO2）/BN Composites,TB332
  2. Research on Welding Characteristics of CO2 Laser-GMA Hybrid Welding for Ultra-Low Carbon Bainitic Steel,TG456.7
  3. Optimizition of Compositions and Processing Parameters and Wear Properties of Cemented Carbides YG11R Modified by Nanosized Rare Earth,TG135.5
  4. EDM Electrode Wear Mechanism and Control Research,TG661
  5. Analysis of Flexspline Stress and Tooth Wear in Harmonic Gear Drive,TH132.43
  6. Study on Contact Fatigue Life Based on Grease Variation with Temperature,TH117.22
  7. Research on Synchronous Acquisition and Processing System Detecting Defocus Signal Based on DSP,TH741
  8. Design and Fault Diagnosis of the Coarse Pointing Control System in Satellite Laser Communication,V443.1
  9. Simulation Analysis on Temperature Stress of RCC Arch Dam and Its Construction Joints Design Research,TV642.2
  10. Analysis and Study of Abutment Stability in Concrete High Arch Dam by Three-Dimensional Nonlinear Finite Element Method,TV642.4
  11. Design of Control System for Laser Beam Steering Device,TM301.2
  12. Research and Design for the Laser’s Power Control System of Laser Direct Writing,TN249
  13. Research on Signal Receiving System of Phase Laser Range Finder,TN249
  14. The Properties of Laser Speckle Based on the Mathematical Morphology,O29
  15. Study of Mutation and Breeding of Griseofulvin Produccing Strain FS80,TQ927
  16. Department of Bi-based Co-based oxide thermoelectric ceramics and thin films,TQ174.7
  17. Characterization and Identification of Maturity of Pig Manure Composting,S141.4
  18. Preparation and Characterization of Polymer Micro/Nano Fibers by Laser Melt Electrospinning,TQ340.64
  19. The Experimental Study of Semiconductor Laser Radiation and 5-FU Sustained Release Repressed Oral Malignant Tumor Cell,R739.8
  20. Preliminary Investigation of Research Intestinal Microflora in Patients with Hepatic Cirrhosis by FISH and LCSM,R575.2
  21. Analysis of the Insulin Dose and Impact Factors of Insulin Pump Treatment of Type 2 Diabetic Patients,R587.1

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > Metallic materials > Steel > Microstructure and properties of steel > Analysis of the steel test
© 2012 www.DissertationTopic.Net  Mobile