Dissertation > Excellent graduate degree dissertation topics show

Research and Design Controllable AC Current Source for Fuel Cell Impedance Monitoring

Author: LuoWei
Tutor: QuanShuHai
School: Wuhan University of Technology
Course: Detection Technology and Automation
Keywords: Fuel cell Controllable current source Online setting Dual-current closed-loop Incremental PI Control
CLC: TM911.4
Type: Master's thesis
Year: 2008
Downloads: 170
Quote: 2
Read: Download Dissertation

Abstract


In the PEMFC system,impedance of the fuel cell is not only the main signs which measurses the situation of the proton and electron transfering,but also decided to stack the key parameters of power generation efficiency.Real-time measurement impedance of fuel cell show the real-time access dynamic information,enhance understanding and analysis of the fuel cell reaction mechanism,has very important significance to improve fuel cell durability and life.In the fuel impedance on-line monitoring system,the controllable AC current source as a source of excitation is particularly critical.This dissertation gives a current source system design which takes DSP as a controller,and through the joint regulation of the DC/DC and DC/AC two-level-power transform to achieve high accuracy,wide range of frequency conversion amplitude-change sinusoidal current output.The output current parameter is set by the main control board of internal impedance test which is connecting network through communication interface.The main content is as follows:Discuss the various components of the current source syetem overall,make a control programme which achieves stable current output by using voltage inverter bridge,and prove the feasibility of the programme by equivalent analysis of voltage inverter bridge.According to the ease of digital effects,the quality of output and the comparative analysis of the two classic SPWM modulation,we adopt the unipolar SPWM modulation and research the control algorithm at the same time.According to specific requirements of current source system,we have given the structure diagram of hardware of the system,and also built a modular hardware platform,including the control module,DC/DC power modules,inverter modules, communication module,protect module and the auxiliary power part.It has concretely finished each module hardware design.On the basis of inverter model in the main circuit,it has established a dual-current closed-loop control model,The simulation results show that current dual-loop control has a good stability and dynamic response.Researching from the traditional continuous PID control to the discrete incremental PI control,it has designed a DSP-based and integral saturated in part incremental digital PI controller.The current source system software design based on DSP controller has been finished,and we especially conducts the analysis research of software design’s several important links.Carried on the current source system’s experiment,the experiment show that the control system has basically achieved the control requirements above-mentioned,and obtained better control effect.

Related Dissertations

  1. Pt -based catalysts of direct methanol fuel cells,TM911.4
  2. Morphology Control Synthesis and Anode Electrocatalysis Performance of Pt/Pd-based Catalysts for Fuel Cell,TM911.4
  3. Study on the Synthesis of the Polypyrrole-Cobalt Oxides and Their Catalytic Behavior for the Electroreduction of H2O2,O643.32
  4. LSGM electrolyte thin films and electrochemical properties of,TM911.4
  5. The Algorithm Researches of Novel Wide Area Backup Protection for Power Grid,TM774
  6. Resistant chromium poisoning , high-performance solid oxide fuel cell cathode materials research,TM911.4
  7. Microbial fuel cell processing aniline and nitrobenzene wastewater,TM911.4
  8. Heat Distribution Model of Direct Hydrocarbon Solid Oxide Fuel Cell,TM911.4
  9. Study of Optimal Parameter Matching and Optimal Control for Fuel Cell Electronic Vehicle with Ultracapacitor,U469.722
  10. Fabrication of Anode/Electrolyte Bi-Layer for Solid Oxide Fuel Cells by Single Step,TM911.4
  11. Research on Adaptive Energy Management of Fuel-Cell Hybrid Electric Vehicle,U469.72
  12. Microwave pretreatment sludge used in the electrical properties of microbial fuel cell research,X703.1
  13. Design and Research of Protable Digital Product Power Management System Based on Ultra-Low Power Supply,TN86
  14. Double-doped ceria electrolyte materials,TM911.4
  15. Thermal Management and Decoupling Control of the Reformer Model for Solid Oxide Fuel Cell System,TM911.4
  16. The Research and Development of 3.5KW PEMFC Cogeneration System,TM911.4
  17. Fabrication and Performance Research of Large Size Half Cell by Tape Casting,TM911.4
  18. Composite Anode Materials Based on Mn/Fe Doped （La, Sr）CrO3-δ for Solid Oxide Fuel Cell,TM911.4
  19. Research on Copper-Based Anode Material of Direct Hydrocarbon Fuel Cell,TM911.4
  20. Study of SOFC Anodic Nano Composite Powder and Technique for Battery Molding,TM911.4
  21. Conductive Polymer Composite Film Modification Electrodes and Their Application,O631.3

CLC: > Industrial Technology > Electrotechnical > Independent power supply technology (direct power) > Chemical power sources,batteries, fuel cells > Fuel cell
© 2012 www.DissertationTopic.Net  Mobile