Dissertation > Excellent graduate degree dissertation topics show

Development of Film Thickness and Experiments Study on Lubrication in Cold Rolling

Author: FanZhongMian
Tutor: ZhangXiaoMing
School: Northeastern University
Course: Materials Processing Engineering
Keywords: cold rolling lubrication minimum film thickness friction coefficient
CLC: TG335.12
Type: Master's thesis
Year: 2009
Downloads: 111
Quote: 2
Read: Download Dissertation

Abstract


Lubrication in cold rolling process is used not only to control friction, but also to control surface quality and thermal chamber. Successful cold rolling of strip at high speeds requires an optimum presence of lubricant film thickness at the contact. An over thick lubricant film may result in mattes surface, while too thin film might allow metal-metal contact, which may be responsible for roll wear and sheet surface defects. In order to have a better control on rolling process the awareness for the prediction and maintenance of desired minimum film thickness in the inlet zoon as a function of process variables such as roll speed reduction ratio, material parameter, and slip are essential. The factors that affect the minimum film thickness have been done and a mathematical model has been developed for the calculation of minimum film thickness use Matlab. What is more, the calculation model has been proved practically in the experiment. The main work in this thesis as follows.(1) On the relevant research about minimum film thickness, a new minimum film thickness was developed. Compared with other film thickness formula, the priority is that the influence of temperature was taken into consideration accurately and it can be used at high speed cold rolling, the speed could be more than 20m/s.(2) A calculation program under "Matlab", named as "minimum film thickness" was developed. Compared the theoretical results with the data got from experiments and relevant researches, proved that the minimum film thickness were accurate.(3) The cold rolling lubrication experiments in lab were done, and developed the relationship between friction coefficient and minimum film thickness and believed that each factor affect the friction coefficient through minimum film thickness. This model can improve the prediction accuracy of rolling force.(4) Use the minimum film thickness and the data got from the lab experiments analysis the factors that affect the cold rolling lubrication, pave the theoretically way for the mechanism research of lubrication and developing new lubrication oil.(5) The trends of roughness were analyzed in cold rolling process, which can be useful for the prediction of strip final roughness.

Related Dissertations

  1. The Air Linear Motion Reference Design Based on Multi-Throttle,TG83
  2. Research on Caster Oil-based Cold Rolling Oil,TE666
  3. Research on Reversible Single Stand 4-high Cold Rolling Mill Gauge Control System,TG334.9
  4. Research of the Measurement of Oil Mist Density Based on Polarization Method,TH117.2
  5. Marine water lubricated bearing lubrication pump performance test study,TH133.3
  6. Manganese steel cold rolling reverse transformation and mechanical properties of annealed,TG335.12
  7. Dowa tilting pad journal bearing lubrication properties of thermal,TH133.3
  8. Research on Ground of Deformation Simulation Test-bed,TU433
  9. Response Analysis of Parallel Composite Isolation,TU352.12
  10. Development of Closed-loop Driving Simulator in Complex Environment and Research on Handling Characteristics,U461.6
  11. Research and Development of a Portable Road Friction Coefficient Tester,U416.2
  12. Lubrication Performance and Thermal Structure Coupled Analysis of Water Lubricated Rubber Alloy Slab Bearings,TH133.3
  13. Optimization Design of the Mould of Water Lubricated Rubber-alloy Bearings,TH133.3
  14. Preparation of Soft Clay for Bearing Capacity of Model Tests and Study on Installation of Suction Caissons,TU43
  15. Study on the Friction Performance of MAO Film on TC4 Titanium Alloy,TG174.451
  16. Study on Preparation and Tribological Properties of Copper Matrix with SiC and Carbon Onions Self-lubricating Composites,TB33
  17. Numerical Simulation of Hot Forming Polycarbonate Sheet and Experimental Resaerch on the Forming Limit and Friction,TQ323.41
  18. Flow simulation based on network analysis of diesel engine lubrication system,TK423
  19. The Experimental Research of Journal Bearing Based on Oil-Gas Lubrication,TH133.31
  20. Influence of Surface Texture on Tribological Property of Piston Ring/Cylinder Tribopair,TH117.1
  21. Theoretical Study on the Performance of Mechanical Seals with Deep Grooves Used in Reactor Coolant Pump,TH136

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metal pressure processing > Rolling > Rolling process > Rolling method > Cold-rolled
© 2012 www.DissertationTopic.Net  Mobile