Dissertation > Excellent graduate degree dissertation topics show

Research of Fireproof and Heat-insulation Composite Fabrics with Shape Memory Alloy

Author: ZhengHuiQin
Tutor: LinLanTian
School:
Course: Fashion Design and Engineering
Keywords: composite fabrics shape memory spring high temperature fire protectionheat insulation aerogel felt TPP test numerical simulation
CLC: TS195.6
Type: Master's thesis
Year: 2011
Downloads: 64
Quote: 0
Read: Download Dissertation

Abstract


According to the instantaneous high-temperature fire environment that firefightersmay face, a kind of composite fabrics which could provide adequate protection for specialparts of the body (such as the back) in such environment was researched. The fabric is notonly fire protection and heat insulation, but is also very light. From outside to inside, thefabric is composed of a fireproof outer layer, a reflective layer, a heat-insulation layer and aflame-retardant inner layer. In this paper, theoretical analysis was used to establish therequirements of the composite fabrics and each layer. According to the requirements,appropriate materials for each layer were selected, and the relative performance of thematerial was tested. The application of air layer and silica aerogels as the heat-insulationlayer was proposed. Fireproof and heat-insulation performance of several differentcombinations were studied. Finally, ANSYS software was applied to stimulate theheat-transfer model for the fabrics. A kind of composite fabrics with excellent performanceof thermal insulation and fire protection was obtained. The contents and conclusions of thispaper can be summarized as following four aspects.First, each layer’s performance requirement of the composite fabrics was studied. Therequirement for the using temperature and limiting oxygen index of the fireproof outerlayer, reflectivity of the reflective layer, insulation layer’s using temperature and thermalconductivity, flame-retardant layer’s using temperature and flammability were defined.Through theoretical analysis, appropriate materials were selected as the layers of thecomposite fabrics and their relative performance was tested. The results showed that basaltfiber could withstand high temperature above800℃and have insulating properties, whichis suitable for the outer layer; aerogels have a low-density, high using temperature andpermanent insulation performance, which is suitable for thermal layer material; shapememory spring’s of action temperature is about45℃, with a certain degree of elasticity, can form a20mm insulating air layer; PSA fabric has high using temperature, good flameretardancy and thermal stability, can be used as the flame-retardant inner layer.Second, the composite fabrics’ performance requirements were established. Thethermal protective performance (TPP value) is required greater than60. The fireproof andheat-insulation is defined as: after heated by800℃flame for60seconds cold facetemperature of the fabric is not higher than50℃, after heated by450℃flame for180seconds cold face temperature of the fabric is not higher than50℃. Instantaneousthermal-insulation composite fabrics with shape memory alloy and the permanent-insulation composite fabrics with aerogels were studied respectively, including theircombination way, thermal protective performance and heat insulation performance.ORIGN analysis software was used to analysis the experimental data. The results showedthat: instantaneously insulate composite fabrics’ TPP value is47.6, the cold facetemperature reached to50℃after burning on the450℃flame for20seconds,, the coldface reached to50℃after burning on the800℃flame for15seconds;permanent-insulation composite fabrics’ TPP value is greater than60, buring on the450℃flame for140seconds the cold face temperature reached to50℃, burning on the800℃flame for44seconds the cold face temperature reached to50℃.Third, the composite fabrics with shape memory spring and aerogels were studied,including the combination way, heat-insulation performance and fireproof performance.And the obtained data was anlysised by using ORIGN analysis software. The resultsshowed that: burning on the450℃flame, the temperature of the composite fabrics’ coldface was never higher than50℃, burning on the800℃flame for90seconds the compositefabrics’ cold face temperature reached to50℃. TPP test showed the thermal protectionperformance is better than60, both the thermal protection performance and fire-protectionperformance are excellent.Fourth, the heat-transfer model of the fabrics was stimulated by ANSYS. The resultsof simulation and results of experimental matched well, especially single heat transfermodel for aerogels. The model is basically effective.

Related Dissertations

  1. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  2. Study on Springback of High-Strength Steel Stamping,TG386
  3. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  4. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  5. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  6. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  7. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  8. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  9. Numerical Simulation of SNCR Process of a 600MW Utility Boiler,TK222
  10. Numerical Simulation of Biomass Direct Reburning,TK16
  11. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  12. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  13. Study on Gas-Solid Two-Phase Flow in Spouted Beds,TK173
  14. Experimental Study and Numerical Simulation on Aerodynamic Field of Tangential Bias Swirl Burner,TK223.23
  15. Characteristic Study of Combustion in Central Reverse Flame Chamber,TK223.21
  16. Numerical Simulation and Contrastive Analysis of Labyrinth Seals and Leaf Seals,TK263.2
  17. Numerical Study on Phosphorus Distribution in Water Environment of the Three Gorges Reservoir,X832
  18. The Design and Performance Simulation of External Valve Small Displacement Pump,TE933.3
  19. Analysis of the Impact of Tailings Dam Stability under Seepage Role,TV649
  20. On the Simulant Research of the Pneumatic Cleaning Mechanism of Mini-combine Harvester,S225.3
  21. Adult OSAHS Preoperative and Postoperative Nasal and Pharynx Cavity and Soft Palate of the Numerical Analysis of Fluid-structure Interaction,R766

CLC: > Industrial Technology > Light industry,handicrafts > Textile industry,dyeing and finishing industry > Dyeing and finishing industry > Finishing > The finishing of a variety of fiber and its products
© 2012 www.DissertationTopic.Net  Mobile