Dissertation > Excellent graduate degree dissertation topics show

The Research on Performance for the Impeller Cutting of the Centrifugal Pumps with Low Specific-speed Based on the CFD

Author: YangDengFeng
Tutor: ZhaoWanYong
School: Lanzhou University of Technology
Course: Fluid Machinery and Engineering
Keywords: low specific-speed centrifugal pump cut area ratio principle numericalsimulation pressure pulsation
CLC: TH311
Type: Master's thesis
Year: 2012
Downloads: 52
Quote: 0
Read: Download Dissertation

Abstract


Usually,we defined the ns of the centrifugal pumps with low specific-speed is between thirty and eighty,this pump is widely used in the oil,chemical industry,and diggings field because of its small flow and high head characteristic. The flow of the centrifugal pumps with low specific-speed inside is very complex.the flow is full of the turbulence,it takes the vortical motion and it can not be press,so use the common experiment is very difficult to research its inside flow.At present,the CFD is used to analysis the flow of the pump,and is a very effective method.In order to achieve the performance demand of the centrifugal pump, expand the scope of the centrifugal pump,cut the outer diameter of the pump impeller is a way we usually adopted. The cut of the conventional method is selected the high performance centrifugal pump,and accordance with the current formula calculation, fixed, and then implement cutting. the Centrifugal pump impeller outside diameter will be changed after the cutting,and make its internal flow compared with prototype pump there are some differences. In this paper, A total of five times cut to the MH-47-100type low rotation speed centrifugal pump was carry out,and the characteristic curve was getted. After five times cut, each performance curve was analyzed and compared. Discussed the low speed centrifugal pump performance changes after the impeller diameter was cutted.In this paper, the mainly research for the MH-47-100type centrifugal pumps with low specific-speed is that:l:Cut the Centrifugal pump impeller outside diameter for five times,use the CFD carry out steady Numerical simulation to Each model.2:Calculated the area ratio of each model that before and after cutting, According to the existing literature that the high efficient area,get the conclusion that all of the models were fall into the high efficient area.3:Base the steady Numerical simulation, Did the unsteady numerical simulation to the the prototype pump, and after8mm and40mm cuted two models, Analysis under different pump impeller outer diameter the change of the flow.4:In the export of the impeller and the isolated tongue set up nine points, analyzes under the different diameter of the impeller export surface and volute outlet pressure pulsation. The mainly conclusions are obtained through the study is that:1:After the impeller outer diameter of the centrifugal pumps with low specific-speed with a small cut,the flow of its inside is similar;but after the impeller outer diameter with large cutting,the flow of its inside is no longer similar.2:After the impeller outer diameter with a small cut,the characteristic curve of the pump is relatively similar;and after large cutting,the characteristic curve of the pump is no longer similar.3:Through the phenomenon that the models were fall into the area of high efficient, Shows that the efficient to area of the statistical law have the certain reference value.4:After cutting the outer diameter of the impeller, the effect on the impeller of internal static pressure value is less than the centrifugal pump volute internal static pressure value,meanwhile with the increase of the cutting, the static pressure values of different points in the Pump were decreased.5:Through the unsteady simulation get the three models of different times pressure pulsation, And through the contrast analysis to get that, Impeller outside diameter reduced, Pressure pulsation intensity decreases.

Related Dissertations

  1. The Research of the Text Extraction Method Based on Spectral Cut,TP391.41
  2. Design and Experiment Study on Multi-Functional Machine of Joint Harvesting Combined with Ditch Buried Grass for Rice and Wheat,S224.29
  3. Study on Transformation of Cut Chrysanthmemum with DdICE1 Gene,S682.11
  4. Studies on the Relationship between Lignin and Bent Neck and Aphid Resistance in Spray Cut Chrysanthemum,S682.11
  5. Study on Comprehensive Evaluation System of Cut Chrysanthemum and Genetic Analysis of Main Characters,S682.11
  6. Influence of Different Plant Growth Regulators on Vase Life and Physiological Action of Cut Chrysanthemum,S682.11
  7. Effects of Elevated CO2 on Vase Life of Cut Flowers and Investigation into Reproductive Barriers in Crosses of Flower Lotus (Nelumbo Nucifera),S682.11
  8. Predicting the Coupling Effects of Water and Nitrogen on External Quality of Standard Cut Chrysanthemum in Solar Greenhouse,S682.11
  9. A Model for Predictingrowthdynamic of Cut Lilium in Greenhouse,S682.29
  10. Quantifying the Effects of Water and Nitrogen Coupling on the Growth of Standard Cut Chrysanthemum ’Jinba’ in Solar Greenhouse,S682.11
  11. Simulation Model on Development, Growth and Quality for Cut Tulip in Solar Greenhouse,S682.263
  12. Research rotodyne cutting damage yuan formation mechanism of high-voltage driver,TJ811
  13. Research of Color Image Segmentation Method and Its Application Based on Visual Features,TP391.41
  14. Research on Matrix Material of the New Paper-cut,TS174
  15. The Restricted Edge-connectivity of Order k of Bubble-sort Graphs,O157.5
  16. Study on the Mechanical Properties of Short Cut Aramid Fiber Reinforced Cement Mortar Composites,TU578.1
  17. Research of Wire Cut Electrical Discharge Machine Control System Based on ARM,TG484
  18. Research on Grinding Geometry and Grinding Force of High-Hardness Sphere Grinding,TG580.6
  19. Study on High Temperature Air Combustion of C3Hs in Flue Gas Auto-circulation Heating Furnace,TK16
  20. Piston refrigeration compressor PV diagram of the test system,TB652
  21. Experimental, Study and Numerical Simulation for Oxy-Fuel Combustion Characteristic of Pulverized Coal-Fired Boiler,TK229.63

CLC: > Industrial Technology > Machinery and Instrument Industry > Pump > Vane pump > Centrifugal pump
© 2012 www.DissertationTopic.Net  Mobile