Dissertation > Excellent graduate degree dissertation topics show

Key Technologies Research of EPS Controller for Commercial Vehicles Based on CAN Bus

Author: WangTao
Tutor: LiuJingYu
School: Chang'an University
Course: Vehicle Engineering
Keywords: CAN bus Commercial vehicle EPS Assist characteristic PID Bench testing
CLC: U463.4
Type: Master's thesis
Year: 2012
Downloads: 39
Quote: 0
Read: Download Dissertation

Abstract


The EPS system is a new-high-tech that follows modern vehicle development topicclosely, which represents the future of automotive steering technology development trend.The application scope of the EPS system is range from the first passenger cars to the largercommercial vehicle direction. With the development of the modern automobile electronicnetwork technology, as well as the CAN bus communication appears, which provides a newrevelation for the development of the EPS system that must support the CAN buscommunication protocols, so as to communicate with other electronic control systems in thecar, which can increase the power performance and improve the vehicle’s active safety.Therefore, development of commercial vehicle EPS controller that supports CAN bus willhave important utility value and practical significance.The thesis selected a medium truck loading4T as the target, through the analysis of thetarget model’s dynamic characteristics, we got the key control parameters of the power curveand then developed MC9S12XDP512processor as the core of the controller, which supportedCAN communications. In terms of the hardware circuits, the author established the controlnodes network of the EPS, mainly developed the power conversion circuit, the input signalregulate circuits, the power drive circuit, the CAN communication circuit, the fault detectioncircuit, then processed the H-bridge drive circuit simulation analysis with Multisim10.1, theresults of which showed that the circuit has a stable and reliable electrical characteristics. TheSoftware was added modular design concept to optimize the power control mode of EPSsystem, then writed the software control program, for the power motor current servo control,the paper proposed an incremental digital PID closed-loop control software design scheme.The thesis added the motor compensation control strategy in the basic control strategy of theEPS, and introduced the actual steering wheel angle signal in the back to control mode,meanwhile, used the measured motor speed as the basis parameters in the damping controlmode. Finally, through the bench performance testing, which the result shows, thecorresponding controller module hardware and software design has been basically to meet thecontrol requirements.

Related Dissertations

  1. Development of GJB1188A Bus Signal Monitoring and Recording Device,V248.2
  2. The Design and Optimization of Locomotive Signal Testing System Based on ARM9,U284.91
  3. Study on the Locomotive Dynamic Supervision System,U284.48
  4. The Inductive Load Based Vehicle Body Network Control System,U463.6
  5. The Study of Control Algorithm for Automotive Power Window Based on Lin Bus,U463.6
  6. Single Neuron PID Control for Electro-Hydraulic Servo Unit of Ship Rudder,U666.152
  7. Design of Control System for Laser Beam Steering Device,TM301.2
  8. Research on Induction Motor Vector Control System Adapting Multi-Bus Communication Mode,TM346
  9. Research and Design for the Laser’s Power Control System of Laser Direct Writing,TN249
  10. Research on Temprature Controling Technology of Laser Diode with Thermoelectric Cooler,TN248.4
  11. Research on High-Performance Computer I/O Bus,TP336
  12. Development of High Speed Data Acquisation and Playback Module Based on PCI Express Bus,TP274.2
  13. Development of the Digitizer Based on PCI-E Bus,TP274.2
  14. Research on Ducted Fan Unmanned Vehicle Autonomous Modeling and Control Strategies,V249.122
  15. Research on Temperature Control System for Laser Diode,TP273
  16. Design of LXI 1553B Bus Communication Module,TP273
  17. Research on the Control and Remedy of Nanopositioning Stage Drived by Piezo Material Lead Zirconate Titanate,TP273
  18. Design and Study of Temperature Chamber Control System in Servo Table,TP273
  19. Design of the Main Controller in Automotive Body Network Control System,TP273
  20. Design the Control System of Ocean Wave’s Simulation Table Based on Theory of Fuzzy Turning PID,TP273.4
  21. Research on Key Technologies of Automatic Steel Wire Galvanizing Production Line Based on Gas Reduction Method,TQ153.15

CLC: > Transportation > Road transport > Automotive Engineering > Automotive structural components > Steering system
© 2012 www.DissertationTopic.Net  Mobile