Dissertation > Excellent graduate degree dissertation topics show

Research and Development of High Strength Ultra Low Carbon Bainitic Steel

Author: XiaWenZhen
Tutor: ZhaoXianMing
School: Northeastern University
Course: Materials Processing Engineering
Keywords: ultra-low carbon bainite steel high strength high toughness microstructure andproperty relaxation
CLC: TG142.1
Type: Master's thesis
Year: 2012
Downloads: 7
Quote: 0
Read: Download Dissertation

Abstract


With the development of building facilities in recent years, the steels which have more high strength and toughness are needed, so the concept of the third generation low alloy steel has been put forward by the third "973plan", and it demands to greatly improve the strength and toughness and obtain its production technology. Base on the requirement mentioned above, a composition of ultra-low carbon bainitic steel (ULCB) was designed in this paper. Through the thermal simulation experiment, the hot working characteristics of ULCB steel were studied during hot deformation and the phase change rule was also investigated during continuous cooling. The effects of heat treatment parameters on microstructure and properties of ULCB steel were also studied by heat treatment experiment. The main works involved are as follows:1. The recrystallization behaviors were investigated by single and double pass thermal simulation experiment with dynamic recrystallization activation energy Qd=402kJ/mol and static recrystallization activation energy Qrex=395kJ/mol, And the relations between critical strain, peak strain and peak stress and Zener-Hollomon parameter being determined and the functiones of dynamic recrystallization dynamics and static recrystallization dynamics were established. The curves of continuous cooling transformation of ULCB steel were drew by thermal simulation experiment of CCT.2. The effects of two-stage controlled rolling on offline microstructure and properties of ULCB steel were studied by double pass thermal simulation experiment. At the same rolling reduction, hardness first rises then falls with the increasing of rolling reduction in austenite non-recrystallization zone.3. The effects of heat treatment which contains Q-T process and offline-relaxation on microstructure and properties of ULCB steel were also investigated.(1) Through setting a series of different parameters of offline quenching, the effects of offline quenching on microstructure and properties of ULCB steel were discussed and the best quenching process is900℃,50min.(2) Residual austenite between bainitic lath decomposes gradually and the bainitic lath will gradually merge and granular bainite may appear with increasing tempering temperature. Coarse quasi-polygonal ferrite which has little dislocation is produced at about700℃. Tempered microstructure becomes more and more stable. The yield strength increases, then reduces sharply as tempering temperature rises, and the yield strength is only710MPa at700℃. The higher the tempering temperature is, the higher yield ratio is, and the better the plasticity is.(3) In offline relaxation process, tensile strength increases then slightly decreases with relaxation time, when the specimens are air cooled above two phase zone. And the tensile strength reaches a maximum1034MPa when the specimen relaxes about20seconds. When the specimens are air cooled into two phase zone, the yield and tensile strengths decline sharply, and elongation increases.

Related Dissertations

  1. Study on Springback of High-Strength Steel Stamping,TG386
  2. Study on Preparing the High Performance Fiber and Nonaporous Fiber by High Viscosity Nylon-6,TQ342
  3. Soft tissue crush injury in rats induced reactivity of isolated thoracic aorta changes,R686
  4. The Effect of the Linden Relaxation Technique on Anxity and Heart Rate Variability of Long-term Naval Sailors on Surface Ship,B842.6
  5. Preliminary Study of the MRI Diagnosis and Differential Diagnosis in Multiple System Atrophy , Progressive Supranuclear Palsy and IPD,R445.2
  6. Study on Change Detection Technology Based on Polarimetric SAR Data,P237
  7. The Study on Strain Distributions and Equilibrium Morphologies of Anisotropic Quantum Dots,O471.1
  8. Study on Cold-rolled and Annealing Process of Low-carbon High Strength Steel with Al,TG156.2
  9. Flexible Manufacturing Technologies of 345MPa～460MPa Grade High Strength and Low-alloy Steel Plates,TG335.11
  10. Variational multiphase image segmentation model and Split Bregman iterative algorithm,TP391.41
  11. Development of Hot-rolled and Ribbed Round Steel Bars 25CrMoA for Ultra-high Strength Oil Sucker,TG335.11
  12. The Effects of Self-relaxation on Sleep Quality and Cognitive Functions of the Elderly,R473.2
  13. The Effect on Microtexture of Fine Grain High Strength IF Steel after Annealing,TG156.2
  14. And frequency vibrational spectroscopy (SFG) Relaxation Behavior of Polymer Surfaces,O631.3
  15. The Research of Nonlinear Optical Properties Based on the Photosensitive Molecular Orientation,O437
  16. The Research on Anealing Process and the Second Particles Precipitation Behavior of Fine-grain and High-strength IF Steel,TG156.2
  17. Fundus Image Segmentation Based on SVM and Template Matching,TP391.41
  18. Analysis of Power System Reactive Power Based on Power Flow Tracing,TM714
  19. Experimental Study on Machining Ultra-High Strength Steel 30Cr3SiNiMoVA by Milling Instead of Grinding,TG54
  20. A Study of Electroplastic Roll Hemming Process,TG306
  21. Investigations on Wear Resistance Characteristics of Die Materials for Blanking DP780 Based on Edge Quality,TG385.2

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > Metallic materials > Steel > Microstructure and properties of steel
© 2012 www.DissertationTopic.Net  Mobile