Dissertation > Excellent graduate degree dissertation topics show

Research on the Tooth Modilfication of2.5MW Wind Power Gearbox

Author: LiuDan
Tutor: WangChunXiu
School: Ningxia University
Course: Mechanical Manufacturing and Automation
Keywords: gearbox Romax WIND modeling gear modification three elements of modification
CLC: TH132.41
Type: Master's thesis
Year: 2013
Downloads: 118
Quote: 0
Read: Download Dissertation

Abstract


At present, gearboxes are faced with the problems of high failure rate, vibration noise, short service life. Gear modification has an effective in reducing vibration and noise, extending life which has been proven by practical experience at home and abroad for many years, therefore, studying gear modification of high-power wind gearbox is very important.The thesis main use the2.5MW gearbox as the research object,and simulate the performance of2.5MW gearbox. The thesis research gear modification of the parallel gears of2.5MW gearbox in order to obtain the method and parameter of modification of2.5MW gearbox. The main research work of this thesis are as follows:(1) To analysis the principle of profile modification and lead modification. Due to the high-power MW wind gearbox are running under the bad environment, the load is very unstable, a single modification method does not work efficiently, comprehensive all kinds of modification methods are put forward and adopted which can more effectively reduce the fault rate.(2) The modeling of2.5MW gearbox are creacted by using CAE and Romax WIND software.(3) To simulate the static analysis of the gearbox through the Romax WIND software under the equivalent loads. According to the stress on the gear shaft, deformation of that, the load distribution on the tooth surface of gear and transmission error, etc. And the length, quality and curve of modification of the high-speed and medium-speed was determined in the end.(4) As wind gearbox are running under alternating load,to simulate the modification gearbox that is operated by Romax WIND software in the specific load, which can demonstrate the rationality of modification parameters. And the change of security strength of gear tooth are discussed.(5) Simulation of high-speed and medium-speed gear pairs gear modification according to mapping data, compared with the modification effect between the actual modification and the modification from the thesis. And analysis reasons for different results. Finally, the gear dynamic incentive theory are stated and the dynamic performance index are analyzed.

Related Dissertations

  1. The Realization of Coal Liquefaction in the Continum Model System and the Experimental Research of Coal Liquefaction,TQ529.1
  2. Soft Sensor of Naphtha Dry Point on Support Vector Machines Regression,TE622.1
  3. Research on Mechanism Analysis and Modeling Simulation of Horizontal Well Tractor,P631.83
  4. Coupled Calculation of the Solidification Paths of Ternary Eutectic Alloys Based on Thermo-Calc,TG111.4
  5. Tooth Profile Modeling and Machining Error Analysis of the Face Gear,TH132.41
  6. Analysis and Study of Abutment Stability in Concrete High Arch Dam by Three-Dimensional Nonlinear Finite Element Method,TV642.4
  7. Research on HID Lamp Rectifying Effect,TM923.32
  8. Research of Visualization Technology in the Virtual Test of Missile,TP391.9
  9. Aerial Target Anti-interference Recognition and Tracking System,TN215
  10. Army logistics material management system design and implementation,TP311.52
  11. Study on Model-Based Visualization of Wheat Root Systems,S512.1
  12. Social insurance agencies risk prevention research,F842.6
  13. Moving target trajectory analysis based Intelligent Traffic Monitoring System,TP277
  14. Airborne radar antenna pedestal rapid design systems research and development,TN959.73
  15. System Design and Experimental Study of Virtual varying cantilever,TJ303
  16. From the evolution of the shape of the car to see the future of automotive design,U462
  17. The Study of the Lighting Art for Interior Decoration,TU238.2
  18. The Research of Design Characteristics of Shaanxi Weibei Column Bases,TU-80
  19. Modelling Pattern of Realistic Painting,J212
  20. Research and Implementation of Distributed Data Integration Visual Modeling,TP311.52
  21. The Research on the Relationship between Equity Ownership Structure、 R & D Investment and Enterprise Value of High Tech Listed Companies,F271

CLC: > Industrial Technology > Machinery and Instrument Industry > Mechanical parts and gear > The transmission mechanism > Meshing > Gears and gearing
© 2012 www.DissertationTopic.Net  Mobile