Dissertation > Excellent graduate degree dissertation topics show

Study on A Reduction-bonding Process for Manufacturing Stainless Steel Clad Strip

Author: DongHaiXue
Tutor: JingYuAn
School: Liaoning University of Science and Technology
Course: Materials Processing Engineering
Keywords: Reduction roll bonding bonding strength Stainless clad strip
CLC: TG335.11
Type: Master's thesis
Year: 2012
Downloads: 102
Quote: 0
Read: Download Dissertation

Abstract


In this study,the stainless were successfully bonded by hot rolling in high purity hydrogen ,which were with 304 stainless steel and 235 carbon steel for raw materia. The technology production cost is low,can continuously manufacture and improve the efficiency.This test composited hot-rolled strip with stainless clad which was under the premise of hot-rolled strip surface oxidized scale reduced in high purity hydrogen.The text analied the influence of each reduction parameters to carbon-steel surface oxidation conversion, iron sheet surface and the cross section shape and the influence of each rolling parameters to the composite microstructure and bonding strength of the clad .Through the research of morphology change rule of strip surface oxidized scale and the test of bonding strength of the clad ,the results indicated: the transformation rate of oxidized scale was gradually increasing with the rise of temperature, gas flow and reduction time.The unit area weight loss of iron oxideis was 4.53g/m2 at the temperature of 700℃, the gas flow of 30L/h and the reduction time of 1 min, the surface remained lots of oxidized scale.The unit area weight loss of iron oxideis was 7.2g/m2 at the temperature of 900℃, the gas flow of 100L/h and the reduction time of 7min, the surface was clean.The shearing strengths and peel strength of clad strip vary directly as deformation rate and bonding temperature.The minimum shearing strength and peel strength can reach 224MPa and 212 N·mm-1 respectively at 950℃by the first pass with deformation rate of 18.5%. The maximum shearing strength is up to 376MPa at 1050℃by the sixth pass with accumulated deformation rate of 70%. The maximum peel strength is greater than the strength of carbon steel substrate.Through the reduction-bonding test achieved the best preparation for composite technology:reduction temperature was 1000℃, reduction time was 6min, the gas flow was 70L/h, rolling temperature was 1050℃, the first pass deformation rate was 21.6%, the second pass accumulated deformation rate was 40%, the third pass accumulated deformation rate was 51.5%, the fourth pass accumulated deformation rate was61.4%, the fifth pass accumulated deformation rate was 68.7% , the sixth pass accumulated deformation rate was 74.8%

Related Dissertations

  1. Application of Additives’ Drag Reducing Technology in District Heating System,TU995
  2. Research and Implementation of the Conflict Resolution in Process Modeling of Magic Platform,TP311.5
  3. Based on Rough Set of Urban Areas When Traffic Green Control System Research,TP18
  4. Study on Green Finance Promotes Industrial Restructuring,F832;F205
  5. Investigation of Plasma Sprayed NiCr-Cr3C2 Coating on Mould CrZrCu Alloy Plates,TG174.442
  6. Preparation and Characterization of SiC Films and Nanowires,TB383.2
  7. Reduction Algorithm for Research and Application Based on Variable Precision Rough Set,TP18
  8. The Synthesis and Characteristic of Micro-particle Silver Used for Conductive-paste,TB383.1
  9. The Rheological and Adhesion Properties of EVA-based Hot Melt Adhesives,TQ436.4
  10. The Study of Selective Catalytic Reduction of NO by CH4 in Combination of Non-thermal Plasma and Catalysts,O643.32
  11. Structure and Performance of Fe-based Amorphous Coatings Prepared by HVAF and HVOF,TG174.4
  12. Synthesis of Tellurium Nanomaterials by Low Temperature and Direct Growth of Tellurium Nanorod Array on Substrate,TB383.1
  13. Study on the Synthesis of Tio2 /graphene Composite and Its High Photocatalytic Activity for Reducing Cr（VI）,O643.36
  14. Synthesis of Dopa Derivatives and Its Application in Adhesive Bonding,TQ430.7
  15. Effects of Low Temperature Stress and Temperature Rewarming on the Physiological and Biochemical Indexes of Sugarcane,S566.1
  16. Analysis of Slope Stability on Account of Fluid-Structure Coupling Seepage Effect,TU43
  17. Research on Attribute Reduction Based on Equivalence Class with Uncertain Decision Value,TP18
  18. Study on High Wear-Resistant Alloy Steel Flux Cored Wires for Arc Spraying and Its Application,TG422.3
  19. The Research of Asymmetric Reduction of m-phenylpropanol Use Plant Cells,O621.254.2
  20. Research and Implementation of Feature Selection in Chinese Text Classification,TP391.1
  21. The Vehicle Detection and Classification in the Video of Intelligent Traffic Surveillance,TP391.41

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metal pressure processing > Rolling > Rolling process > Rolling method > Hot-rolled
© 2012 www.DissertationTopic.Net  Mobile