Dissertation > Excellent graduate degree dissertation topics show

Research on Reduction Effect of Noise and Vibration during Sheet Metal Blanking Based on Servo Press

Author: HongGuoHua
Tutor: XiaQinXiang；RuanWeiPing
School: South China University of Technology
Course: Mechanical Engineering
Keywords: Blanking process Noise Vibration Servo press
CLC: TG386
Type: Master's thesis
Year: 2011
Downloads: 81
Quote: 0
Read: Download Dissertation

Abstract


Stamping has an important position in mechanical manufacturing industry, and blanking process accounts for about 50% ~ 60% of the whole stamping process.The noise and vibration which influence the sheet forming quality of the part and reduce working life of the press and die set occurred in the blanking process is bad for worker’s health. Comparing with mechanical press, the servo press has a programmable function that allows fully control of the position and velocity of the press slide. The blanking noise and vibration by using servo press is lower than using mechanical press. The research subject is supported by Guangdong Province & Chinese Academy of Sciences Comprehensive strategic cooperation project(No.2009B091300019)—“Development and Application of Multi-Field Integrated Design and Simulation for New Forging Equipment”.The vibration and noise occurred in the blanking process under different parameters based on servo press were mainly studied by the numerical simulation, the theoretical analysis, the engineering simulation and the experimental study; the following works were carried out:1 The valid finite element model is builded and equivalent stress, equivalent strain and mean stress during blanking is analysised. And the variation regulation of blanking force curve and the maximum blanking force under different processing parameter which is the foundation of the research on reduction effect of noise and vibration is discussed. The results show that the maximum blanking force increases with increasing in the material shear strength and sheet thickness;the maximum blanking force increase with increasing in the blanking speed but increase barely wit the ration of punch stroke for Q235.2 The forecast model of noise pressure level during fracture separating stage of blanking on servo press was established through the theoretical analysis, and the mathematical formula to calculate the noise pressure level was deduced. The variation regulation of noise pressure level under the different material, sheet thickness and blanking speed were obtained based on the deduced theoretical formula. The results show that the noise level increases with increasing in the material shear strength, sheet thickness and blanking speed.3 Three degrees of freedom (TDOF) vibration system based on software Matlab/Simulink during sheet blanking on servo press was established through the theoretical analysis. The variation regulation of press vibration under the different material, sheet thickness, blanking speed and the ratio of punch stroke were obtained. The results show that with the increasing of material shear strength, sheet thickness and the blanking speed, the trend of the press vibration increases; however, with the increasing of the ration of punch stroke before the fracture of sheet, the trend of the press vibration decreases, and the vibration is lowest when the ration of punch stroke is 65%.Finally,blanking experiment was done and the result shows that the validity of the forecast model of noise pressure level and TDOF vibration system .

Related Dissertations

  1. Study on Theory and Experiment of Wire Drawing with Composite Ultrasonic Vibration,TG663
  2. Research on the 6-Dof Fault Tolerant Control of the Vibration Isolation Platform with Eight Actuators,TB535.1
  3. The Study of Control Algorithm for Automotive Power Window Based on Lin Bus,U463.6
  4. The Equivalent Circuit Model of Radial Vibration Mode Piezoelectric Transformer and Its Application,TM406
  5. Design of Servo Control System with Linear Motor Based on Digital Filter Technology,TM359.4
  6. Packet Loss Recovering Technology for Speech Transmission over Network,TN912.3
  7. Research and Implementation on Content-Based Clothing Image Retrieval,TP391.41
  8. Research on Servo Control System of Gyro-Stabilized Platform,TJ765
  9. Research of Acoustic Signal Acquisition System Based on DSP,TP274.2
  10. Study of Acoustical Signal Transmitter Which Based on Sigma-Delta Modulation,TN761
  11. Research on Structural Vibration of Steam Piping System,TK284.1
  12. Moving target trajectory analysis based Intelligent Traffic Monitoring System,TP277
  13. Research on the Prediction of Underwater Acoustic for a Survey Ship and Reduction for Its Noise and Vibration,TB53
  14. The Study of Vibration Signal Analysis System Based on Wavelet Fractal Theory,TN911.6
  15. Research of Adaptive Active Noise Control Based on Neural Network,TP183
  16. The Study of Vibration and Acoustic Noise Suppression in the Switched Reluctance Motor,TM352
  17. Rheological Properties in Processing of Inorganic Rigid Particle Filled Polymer Composites under Vibration Force Field,TQ325.14
  18. Vibrating force field mixed mechanism of plastic extrusion process,TQ320.66
  19. The Structure Design of 2000kN Servo Press for Hot Forming,TG385
  20. Design and Optimation for Cross Flow Fan in Air-conditioning,TH43
  21. The Research and Design of Radio Frequency Monolithic Voltage Controlled Oscillator in 0.18μm CMOS Technology,TN752

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metal pressure processing > Cold stamping ( sheet metal processing) > Cold stamping process
© 2012 www.DissertationTopic.Net  Mobile