Dissertation > Excellent graduate degree dissertation topics show

Random Vibration Reliability Analysis and Research on Solder Joint of PBGA Board Level Assembly

Author: QiXueLi
Tutor: LiGuoYuan；HuangYun
School: South China University of Technology
Course: IC Engineering
Keywords: PCB Assembly Solder Joint Random Vibration Modal Test and Simulation Analysis
CLC: TN405
Type: Master's thesis
Year: 2011
Downloads: 189
Quote: 0
Read: Download Dissertation

Abstract


In the process of transportation and other field applications, PBGA board assembly was easily affected by various random vibration factors, which leaded to high-cycle fatigue failure of solder joint. The application environment of electronic product becomes more and more severe, which will intensify elastic-plastic deformation of assembly’s solder joint, and cause fatigue damage rapidly cumulative, and finally result in failure of solder joint and even device. Therefore, the dynamic characteristic of PCB assembly and vibration reliability of solder joint becomes one of the focus points of the reliability.In order to explore the dynamic characteristic of board assembly, the PBGA assembly test samples which contain daisy chain patterns was designed. Different fixed methods, such as four screws fixation, six screws fixation and two end fixation, were used, and the modal parameters were obtained through modal test and finite element method respectively. After correctness was verified by FEM model and simulation method, the effect of each fixation methods on the first natural frequency of PCB assembly was analyzed. Based on the consistency of the verification of modal simulation and test result consistent, typical fixation method was selected, and random vibration test and simulation of PCB assembly were done. Through random vibration test, most vulnerable to vibration failure of solder joint was confirmed. Based on the random vibration simulation, the maximum stress and strain region was confirmed and the simulation results were compared with the test, and then the model correctness was verified again. Solder joint life prediction method under random vibration environment was proposed. Finally, through modifying the parameters, such as solder joint’s material, diameter, height, PCB’s thickness and fixation condition, modal and random vibration simulation were done. The effect of these parameters on vibration stress and strain of solder joint was researched.Results show that first natural frequency of the PCB assembly increases with the increase in fixed support points. The critical solder joint located on the outmost corner of PBGA which is far away from the fixed points, it is good agreement the first failure solder joint from the vibration test. The crack failure of critical solder joint occurs in the solder close to the device side. Voids in solder joint have harmful influence on the vibration reliability of solder joint. The SMD pad is easier to cause the stress concentration of solder joint comparing to NSMD pad. It can be reduce the maximum stress of solder joint through reducing solder joint height, increasing the solder joint diameter, increasing the thickness of PCB and increasing the numbers of fixation point. It is found that the lead free solder joint has more vibration stress compared with SnPb solder joint. The stress-strain response of interest region could be obtained through the random vibration simulation. Our research results are beneficial to guide the soldering process, to improve structural design, and to analyze the effect of solder joint parameters on the maximum von mises stress. It can also be used as references for increasing vibration reliability of solder joint.

Related Dissertations

  1. Finite Element Analysis and Optimization Design of a Tractor Cab,S219.02
  2. Research on University Students’ Deonitc Reasoning,B841
  3. Study of Modal Characteristics of a Car Body-in-White,U463.82
  4. Dynamic Response and Reliability Analysis of Bus Body,U463.82
  5. Modal Analysis of BIW Construction & Optimization Design in Modal Parameters,U463.82
  6. Research Ofdual-modalbiometric Recognition Based on Fingerprint and Finger-vein on the Match-score Level,TP391.41
  7. Damage Detection to Offshore Platforms Based on Modal Strain Energy Method Considering the Temperature Influence,U674.381
  8. Vehicle-mounted snubbing workover rig derrick Design and analysis,TE935
  9. Direct-drive A / C -axis milling head double pendulum angle structural analysis and performance testing,TG547
  10. Research on the Vibration Performance of Test-bed and Validation of Impeller Strength for Small Centrifugal Fans,TK83
  11. Fluid-Structure Interaction in a Francis Turbine Runner of Splitter Blades,TK733.1
  12. Research on Modal Parameter Identification Based on Ambient Excitation for Offshore Platforms,U656.6
  13. Exact Fixed-Interfacial Substructure Synthesis Using Medium-Order Normal Modes,TB122
  14. A Study of Audio-visual Products and Translation from the Perspective of Multimodal Discourse Analysis,J905
  15. Closed thin-walled beams composite modal damping prediction,TB33
  16. An Analysis of Two Sorts of Rheum, Tune Stylr and Structure in Respect of Qing Opera,J825
  17. Research on Non-backlash Gear Transmission and Controllable Gear Pair,TH132.41
  18. Research on Dynamic Analysis of the Drive between Offset Cylindrical Worm and Face Gear,TH132.41
  19. Research on Vibration Characteristics of High-speed Franking Machine Based on Operational Modal Analysis,TB53
  20. The Finite Element Analysis and Layout Research of Reducer Test Bench Loader,TH132.46
  21. Multi-objective Optimization Design of the Tower Crane Hoist Boom Based on ANSYS,TH213.3

CLC: > Industrial Technology > Radio electronics, telecommunications technology > Microelectronics, integrated circuit (IC) > General issues > Manufacturing process
© 2012 www.DissertationTopic.Net  Mobile