Dissertation > Excellent graduate degree dissertation topics show

Study on Friction and Wear Characteristics of Thrust Bearing in Rotary Compressor

Author: ShengHui
Tutor: YeXiaoMing
School: Huazhong University of Science and Technology
Course: Power Engineering
Keywords: Sliding friction Adhesive wear Boundary lubrication Rotary compressor Thrust bearing
CLC: TH45
Type: Master's thesis
Year: 2011
Downloads: 117
Quote: 0
Read: Download Dissertation

Abstract


The thrust bearing in rotary compressor is always working in the poor state of heavy load,high speed and high temperature .Its lubrication status,friction and wear characteristics play an very important part in the normal operating state of compressor .With considering the wear resistance of the thrust bearing , various main factors influencing wear volume have been analyzed .On the basis of the classical adhesive wear equation, fractional film defect computing has been considered to built a mathematical model for numerical simulation of wear and frictional losses under boundary lubrication condition. A friction and wear characteristics analysis software has been written on the basis of the above work. The software has friendly and convenient user interface.Through the orthogonal experiment,settle load and variable speed experiment, settle speed and variable load experiment in the friction and wear experiment , the influence of load, sliding speed and other external friction conditions on wear volume and friction coefficient was considered . It also corrects some of the parameters in the mathematical model and improves the accuracy of the model.The analysis of experimental results show that the theory value is consistent with the experimental value. Through the orthogonal experiment,it is found that load is the most important factor effecting wear loss and lubricant species is the most important factor effecting friction coefficient. It is found that wear loss increases as load increases and sharply increase when load reaches certain value. Wear loss decrease as speed increases and reach a plateau when speed reaches certain value. Load and speed both have a power function relation with wear loss. Through the simulation experiment of real thrust bearing, frictional power loss first increases and then decreased when the radius of the thrust bearing increases, and it increases when load or speed increases, and it is proportional to both of them. Based on the microscopy of experimental samples, the main wear mechanism of thrust bearing in rotary compressor is adhesive wear.

Related Dissertations

  1. Research on the Key Parameters of Asphalt Pavement Performance Based on Physiological and Psychological Factor,U416.217
  2. Analysis of Powertrain Bearing Wear and Gear Noise,U467.493
  3. Study on the Theory and Applications of the Low Viscosity Lubricants for Green Mining,TH117.22
  4. Study on Temperature and Scuffing Properties for the Sliding Friction Pair on Considering Oil Additives,TH117.1
  5. A Micromechanical Damage Model for Rocks and Concretes Based on the Deformation and Growth of Elliptic Microcracks,O346.1
  6. Study on the Thermodynamic Performance and Frictional Heat Behavior of Metallic Oxides/ Polyamide 1010 Composites,TB33
  7. Zinc alloy ZA30 High Strength Development and tribological properties of,TG146.13
  8. Stress Analysis of Bonded-interface Technique on Subsurface Damage Observations of Brittle Porcelains,R783.1
  9. Design of Three Phase Variable Frequency Miniature Compressor and Portable Refrigerator,TB65
  10. Studies on Preparation and Tribological Behaviors of Chromium Nitride Coatings,TG174.444
  11. An Investigation of TiN Coatings Prepared by Electrospark Deposition under Nitrogen Atmosphere,TG174.4
  12. Study on the Performance of C/C Composites Used as Rolling Seal,TB332
  13. Analysis of Structures with Base Friction Sliding Isolation,TU352.12
  14. Analysis on Porous Aerostatic Bearing Static Performance,TH133.36
  15. Variable cross-section space span steel arch supporting the overall structure of the research,TU391
  16. Finite Element Analysis of Stepped Bearing in ESPCP System,TE933.3
  17. Design of Adjusting Speed Synchronous Motor Series TDZBS,TM341
  18. Study on Digital Control System of Magnetic Thrust Bearing,TP273.5
  19. A new continuous casting machine steel straightening rolls thermal structure stress analysis,TF341.6
  20. Research of the Self-Repairing Adptablitity of Rabbit Skin and Skin Trauma under the Friction Condition,R751
  21. The Supersonic SSymmetric Flow Ideal Gas in Clearance Gradually Increase of Disk Shape,TH133.3

CLC: > Industrial Technology > Machinery and Instrument Industry > Gas compression and transportation machinery > Compressors, compressor
© 2012 www.DissertationTopic.Net  Mobile