Dissertation > Excellent graduate degree dissertation topics show

Study on Fabrication and Oxidation Behavior of 12Cr-ODS Fe-based Superalloys

Author: PengZuoZuo
Tutor: XiongWeiZuo
School: Huazhong University of Science and Technology
Course: Materials Science
Keywords: Fe–based superalloys pressing pressure sintering temperature addition of Si oxidation resistance
CLC: TG132.32
Type: Master's thesis
Year: 2011
Downloads: 54
Quote: 0
Read: Download Dissertation

Abstract


In this thesis, the development of Fe–based superalloys was reviewed. Based on the above work, Fe-12Cr-2.5W-0.4Ti-0.3Y2O3 superalloy powders were prepared by milling. Then the Fe-based superalloys were prepared by annealing, compacting and sintering. The effects of pressing pressure, sintering temperature and addition of Si on microstructure and properties at room temperature of this superalloy and its oxidation behavior were studied, by means of relative density test, hardness test, tensile test, oxidation test, X–ray diffraction analysis （XRD）, optical microscopy （OM）, scanning electron microscopy （SEM） and energy depressive analysis （EDS）.The compact’s density of alloy increased with the increase of pressing pressure, and the curves were liner to parabola. Simultaneity, the porosity of the alloys became smaller. The performance of Fe–based alloy could be optimized by increasing pressing pressure and sintering temperature. The relative density and hardness of the sample pressed under 760MPa and sintered at 1420℃were respectively 86.4% and 145HV.The oxidation degree increased with the elevation of temperature and the extension of time whereas the speed of the mass gain change decreased with the extension of time. And the curves of gained mass were liner to parabola. It can be concluded that oxidation dynamic equations are respectively （?W）4.31=3.99t and （?W）1.97=7.367t from the curves of Fe-based alloys under 650℃and 850℃conditions. When oxidized at 650℃, the oxide layer was compact with comparatively preferable ability to resist from oxidation, while the layer of 850℃was with phenomenon of desquamation and discontinuous of its inside layer which had lost its ability of protection.Relative density, tensile strength and ability of oxidation resistance of Fe-12Cr-2.5W- 0.4Ti-0.3Y2O3 could be obviously enhanced by addition Si. The relative density and hardness of alloy without Si were only 85.9% and 300.96 MPa, while they were up to 97.26% and 692.7MPa after adding Si. The oxide layer of alloy with 0.2% Si was only 40μm and compact even after oxidation at 850℃for 100h. It can be concluded that oxidation dynamic equations of alloy with 0.2%Si is （?W）1.3=0.0367t from the oxidation curves at 850℃.

Related Dissertations

  1. Solid Oxide Fuel Cell ferrite connect the material properties of,TM911.4
  2. Studies of Plasma Spray Metal-Ceramic Compounds Coatings on Q245r Steels,TG174.44
  3. Research of the Microstructure and Properties of B4C and ZrB2/B4C Ceramic Material by Hot-pressure Sintering,TQ174.1
  4. Study on the Preparation and Thermostability for Mechanical Properties Microstructure of Low Density MA/ ODS Nickel-Based Superalloy,TG132.32
  5. Study on the Stoichiometric Ratio of Material and Reducing- Reoxidation Technology of Laminated PTCR,TN605
  6. Research on Microstructure and Properties of Ti(C, N)-based Cermets Coated by Multivariant Nitrides,TG174.4
  7. Titanium sponge reactor temperature oxidation resistant coating Preparation and Mechanism,TG174.442
  8. Boron carbide sintered diamond saw blades in the Applied Research,O474
  9. Simulation Model of Sinter Bed Temperature Field and Experts System of Sinter Quality Optimization,TF046.4
  10. Study on High Silicon Coating by Dc-Plasma Jet Surface Metallurgy,TG174.4
  11. Study on Preparation of high-performance -doped lanthanum lead zirconate titanate piezoelectric ceramics,TQ174.6
  12. Effects of Sintering Temperature and Calefactive Velocity on Properties of Diatomite-based Dental Machinable Ceramic,R783.1
  13. Laser Direct Metal Deposition (DMD) of Ni-Base Superalloy and Its High Temperature Oxidation Resistance,TF124.39
  14. The Study of the Influence of Cr on the Cyclic Oxidation Life of Hot-dipped Coating,TG174.44
  15. The Research of Biological Ceramics Producing with Cotton Stalks,TQ174.1
  16. Study on Ceramic Material of MgTiO3-CaTiO3 System in High Frequency,TQ174.1
  17. Research on Characteristics of Sintered Body Mixed with Sewage Sludge,TU528.0
  18. Studies of High-performance M-Type Strontium Ferrites by Wet Compacting,TM277
  19. Fabrication and Characteristic of Ceramic Coatings on Stainless Steel Substrates,TG174.453
  20. The LTCC the magnetic dielectric composite ceramic preparation and electromagnetic properties of,O482.5
  21. Study on the Diamond Drill Bit Sintering Technics by Hot Pressing,P634.41

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > The alloy learn with a variety of properties of alloys > Special physical properties of alloys > Special thermal properties of alloys > Melting point alloys , refractory alloy , high temperature alloys
© 2012 www.DissertationTopic.Net  Mobile