Dissertation > Excellent graduate degree dissertation topics show

Study of High Power CO2 Laser Welding Technique on T-Lap Joint of 5083 Alumium Alloy

Author: XuChao
Tutor: LiZhuGuo
School: Shanghai Jiaotong University
Course: Materials Science
Keywords: Laser penetration welding Laser-MIG hybrid welding 5083 Aluminum alloy T-lap joint
CLC: TG456.7
Type: Master's thesis
Year: 2012
Downloads: 171
Quote: 0
Read: Download Dissertation

Abstract


With the development of weldable aluminum alloy and global light-duty trend of transport facility,T-joint of aluminum alloy have been widely applied in the aerospace态shipbuilding and automobile industry. Due to equipment limitation, it is difficult to extrude that thickness of T-joint is greater than 4mm. The traditional T-joint fillet weld can not be implementing because of limitation of the structure. In this paper, using high power CO2 laser device, T-lap joint of 5083 aluminum alloy was welded by laser welding and laser-MIG hybrid welding. The influences of laser welding parameters were studied, and the defects of the T-lap joints were also analyzed.Firstly, according to the experimental requirements and welding characteristics of T-lap joint of 5083 aluminum alloy, the positioning device and work fixture were designed and optimized. It provided the equipment condition for the experiment of welding process.Secondly, the influences of laser welding parameters on weld formation of T-lap joint of 5083 aluminum alloy were studied. The parameters include laser power, welding speed, laser position and shield gas flow rate. The result shows:With the increase of laser power or the reducing of welding speed, weld penetration, weld width and junction width increase. Laser position and shield gas flow rate have less of an effect on weld size, but will have greater influence on weld defects. With suitable laser welding parameters, the excellent welding seam on overlap welds of 5083 aluminum alloy T-joint, but the select range of process of parameters is relatively narrow.Thirdly, the influences of laser-MIG hybrid welding parameters on weld formation of T-joint of 5083 aluminum alloy were studied,the parameters include laser power, welding speed, wire feeding rate, heat source distance and assembly gap. The result shows:With the increase of laser power or the reducing of welding speed, weld penetration, weld width and junction width increase. Compared with laser welding, weld appearance by laser-MIG hybrid welding is better. But duo to the increase of weld heat input of laser-MIG hybrid welding, the weld is easier to collapse. It is needed to put two copper plates in both sides of web plate with auxiliary forming. T-lap joint of 5083 aluminum alloy can get maximum penetration and junction width when heat source distance in the range of 2mm to 4mm. With the increase of assembly gap between face plate and web plate, weld defects appear in the aluminum T-lap joint.At last, the defects of the T-lap joints of 5083 aluminum alloy were also analyzed. It is compared between weld appearance by laser welding and laser-MIG hybrid welding. The improvement mechanism of laser-MIG hybrid welding on weld porosity and weld appearance were discussed, and the suggestions for improvement of weld defects were provided.

Related Dissertations

  1. Study on Properties of Laser Welded T-lap Joint of High Strength Low Alloy Steel,TG456.7
  2. Experimental Research on Restraint Grouting-Anchoring Overlap-Joint of Steel Bar,TU375
  3. Study on the Microstructure and Properties of Friction StirWelded Lap Joints of Aluminum Alloy,TG407
  4. The Study of Interface Migrate Behavior in Friction Stir Weld Lap Joint,TG453.9
  5. Optimization on Stress Distribution of Adhesive Single Lap Steel Joint,TG49
  6. Study on Adhesive Bonding Performance of Steel and Aluminum Used on Automobile,TG49
  7. The Aluminum Alloy Adhesive Joint for Auto Industry Mechanical Behavior Simplification and Simulation under Vehicle Collision,TH871
  8. The Member Lap and Joint Design in Structure,TU986
  9. Research on Static Strength Analysis and Strength Prediction of Adhesively Bonded Single Lap Joint for Automotive,U463.82
  10. Micro-area Experimental and Numerical Analysis on Laminated Composites Single-lap Stitched Joint,O346.1
  11. Research on Mechanical Behavior and Simulation and Experiment of Superplastic Forming of 5083 Aluminum Alloy,V250.2
  12. Numerical Simulation and Experimental Study of FSW/SPF to Form Three-sheet Structure of Aluminum Alloy,TG453.9
  13. Research on the Superplasticity of Aluminium Alloy 5083,TG146.21
  14. LNG storage tank welding process and its properties,TG407
  15. Study on the Structure and Properties of Friction Stir Welding 5083 Aluminum Alloy,TG453.9
  16. Structure and Performance of Fsw Joint of AZ31 and 5083 Alloy,TG453.9
  17. Process Research on Fiber Laser-MIG Hybrid Welding Medium Thickness Aluminum,TG456.7
  18. Hot Deformation Behavior and Multi Sheet Structure Forming Processing of Fine-grained 5083 Aluminum Alloy,TG146.21
  19. 5083 aluminum alloy high temperature deformation behavior and superplastic behavior research,TG146.21
  20. Study on Weld Seam Surface Quality of CO2 Laser Welding 5083 Aluminum Alloys for Shipbuilding,TG456.7
  21. Fundamental Research on Laser-MIG Hybrid Welding and Its Application,TG456

CLC: > Industrial Technology > Metallurgy and Metal Craft > Welding, metal cutting and metal bonding > Welding process > Special welding > Laser welding
© 2012 www.DissertationTopic.Net  Mobile