Dissertation > Excellent graduate degree dissertation topics show

Experimental Investigation on New Style of Cemented Carbide Bits and Drilling in Hard Rock

Author: ShenXiaoYing
Tutor: LuYiYu
School: Chongqing University
Course: Safety Technology and Engineering
Keywords: abrasive water jet cemented carbide bit hard rock nozzles numerical simulation
CLC: TD421.25
Type: Master's thesis
Year: 2011
Downloads: 186
Quote: 0
Read: Download Dissertation

Abstract


Gas drainage is one of basic methods to prevent gas disasters in coal mine. but when encountered hard rock in borehole and Shimen coal drilling , the drilling bit will become lower and wear quickly, at the same time, frequent replacement of bit wastes a lot of time, which seriously affecting the efficiency of coal production. It has important significance to find a new way and new type of bit to drilling in hard rock. This paper theoretical analysis of the original three-wing rock-drill mechanism, This paper presents a new method of drilling hard rock which using abrasive water jet breaking out of the pilot hole, and then bit drilling. The new type of bit was designed .Indoor experiment contrast analysis the effect of rock broken by original bit and new type of bit .The main conclusions as follows:①The study shows rock-breaking mechanism of original bit in hard rock drilling. There existing a boss at the end of the drill hole. It needs to overcome the compressive strength of rock for tool to break the boss, at the same time, the cutting force increases. Heat dissipation is difficult because of the boss. As a result of temperature increasing, the tool strength decreases, which reducing the drilling speed.②This paper presented a new way to drilling in hard rock and designed a new type of bit, which includes three parts: the nozzle, pilot drill bit, three-wing basic bit. Abrasive water jet erosion a pilot hole to elimination the boss and pre-broken rock, further ,leading drill bit expand the center hole and broken the rock further, then the three-wing bit drill the hole. Mechanical analysis showed that the bit can change the blade stress state, reduce blade stress and increase hard rock drilling speed.③Abrasive water jet rock erosion performance is the key factors to impact drilling efficiency of new type of bits. The nozzle structure size is limited. The numerical simulation software fluent is used to optimize a fluent nozzle structure, and the jet velocity is the most preferred standard to determine the best nozzle structure: outlet diameter d2 = 3mm, the convergence angleα= 25°, aspect ratio L1/d2 = 2④Through the abrasive water jet erosion of hard rock experiments with optimized nozzle, the influence of nozzle diameter, pump pressure, abrasive concentration on the diameter of punching speed and punching is obtained. The three parameters affecting the impacting speed is nozzle diameter> pump pressure > density of grinding. Considering drilling speed and pilot drill bit blade spacing, there exists a best pump pressure 20MPa and density of grinding 7%⑤The laboratory experiments of hard rock drilling by the original bit, improved bit and new type of bit showed that the improved bit is 1.57 times as fast as the original bit, but torque increased 11.3%, and the wearing increased; new type of bit drilling speed is 3.72 times as fast as the original bit and the torque decreased 34.0%, and no significant wearing. The results show that the drilling speed by new type of bit is high and it can effectively reduce the drill wear.

Related Dissertations

  1. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  2. Study on Springback of High-Strength Steel Stamping,TG386
  3. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  4. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  5. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  6. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  7. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  8. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  9. Numerical Simulation of SNCR Process of a 600MW Utility Boiler,TK222
  10. Numerical Simulation of Biomass Direct Reburning,TK16
  11. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  12. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  13. Study on Gas-Solid Two-Phase Flow in Spouted Beds,TK173
  14. Experimental Study and Numerical Simulation on Aerodynamic Field of Tangential Bias Swirl Burner,TK223.23
  15. Characteristic Study of Combustion in Central Reverse Flame Chamber,TK223.21
  16. Numerical Simulation and Contrastive Analysis of Labyrinth Seals and Leaf Seals,TK263.2
  17. Numerical Study on Phosphorus Distribution in Water Environment of the Three Gorges Reservoir,X832
  18. The Design and Performance Simulation of External Valve Small Displacement Pump,TE933.3
  19. Analysis of the Impact of Tailings Dam Stability under Seepage Role,TV649
  20. Study on Hydraulic Fracturing of Low Permeability Reservoir,P618.13
  21. Numerical Simulation and Experimental Study of Air-Assisted Sprayer of Orchard,S491

CLC: > Industrial Technology > Mining Engineering > Mining machinery > Mining machinery > Underground mining machinery > Rock drill , drill rig > Drill
© 2012 www.DissertationTopic.Net  Mobile