Dissertation > Excellent graduate degree dissertation topics show

Numerical Simulation and Optimization Research on Physical Field in Annular Gap Scrubber

Author: WangFang
Tutor: OuJianPing
School: Central South University
Course: Thermal Power Engineering
Keywords: Bischoff towel gas-liquid two phase flow annular gap scrubber pressure loss numerical simulation
CLC: TF547
Type: Master's thesis
Year: 2011
Downloads: 30
Quote: 0
Read: Download Dissertation

Abstract


With strong ability of top pressure controlling and dust removing, Bischoff tower has been widely used in iron and steel industry. In order to ensure better dust-removing results and higher power generation of unit iron, it is very important to determine the right pressure loss of the tower. Based on the project of "Optimization research in TRT (Top Pressure Recovery Turbine Unit) system", this thesis is aimed at solving the problems about lower power generation of unit iron, which exists in the running process commonly. Based on a large number of literature study and on-site testing research, the physical fields of gas-liquid two-phase flow of the Annular Gap Scrubber (AGE) in Bischoff tower were researched and the operating parameters were optimized numerically. The main contents and conclusions include:(1) The on-site testing research results of the Bischoff-tower in No.6 blast furnace at Lianyuan Iron and Steel Corporation show that, after maintenance, the Bischoff system performs better effectiveness of dust removal and stability in top-pressure, whereas, the pressure loss was bigger and power generation of unit iron was lower.(2) The Annular Gap Scrubber in Bischoff tower was investigated. Then the mathematical model of gas-liquid two-phase flow in AGE was built and studied numerically. Results show that, the inlet speed of droplets and gas is lower, then it grows dramatically after entering the annular gap because the area reduced, and finally the speed reaches its maximum at the outlet of annular gap. After the outlet of annular gap, the air-flow was disorder with obvious vortices which were good for dusting. The simulation results were compared with that of measurements. Because the numerical calculation ignored solid, forecasting results were smaller than testing results with an average relative error about 4%. The simulation results agree well with measurements and the model mainly reflects the law of actual pressure change.(3) Using this mathematical model, the pressure loss in AGE was analyzed numerically under different conditions of annular-gap travel, coal-gas flow, water-gas ratio. Results show that:1) annular-gap travel, coal gas flow and water-gas ratio has different effects in differential pressure of AGE. And the most important factor is annular-gap travel, the second one is coal gas flow, and water-gas ratio is of lest importance/significance); 2) the smaller annular gap travel, the greater pressure loss is. Pressure loss inversely proportional to annular gap travel, and pressure loss decreases more rapidly under smaller travel condition;3) the greater the coal gas flow, the greater the pressure loss is, coal gas flow is proportional to pressure drop, and pressure drops more under smaller travel; 4) water-gas ratio is proportional to pressure drop, the greater water/gas ratio, the greater the pressure drop; 5) When the annular gap travel is controlled between 300-400mm, and coal gas flow controlled between 3.8×105～3.9×105 Nm3/h, the pressure is slightly larger than 30kPa. As a result, it can meet the request of dusting and it is good for the stability of blast furnace top pressure. Finally, it can improve the power generation of unit iron.

Related Dissertations

  1. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  2. Study on Springback of High-Strength Steel Stamping,TG386
  3. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  4. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  5. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  6. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  7. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  8. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  9. Numerical Simulation of SNCR Process of a 600MW Utility Boiler,TK222
  10. Numerical Simulation of Biomass Direct Reburning,TK16
  11. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  12. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  13. Study on Gas-Solid Two-Phase Flow in Spouted Beds,TK173
  14. Experimental Study and Numerical Simulation on Aerodynamic Field of Tangential Bias Swirl Burner,TK223.23
  15. Characteristic Study of Combustion in Central Reverse Flame Chamber,TK223.21
  16. Numerical Simulation and Contrastive Analysis of Labyrinth Seals and Leaf Seals,TK263.2
  17. Numerical Study on Phosphorus Distribution in Water Environment of the Three Gorges Reservoir,X832
  18. The Design and Performance Simulation of External Valve Small Displacement Pump,TE933.3
  19. Analysis of the Impact of Tailings Dam Stability under Seepage Role,TV649
  20. Study on Hydraulic Fracturing of Low Permeability Reservoir,P618.13
  21. Numerical Simulation and Experimental Study of Air-Assisted Sprayer of Orchard,S491

CLC: > Industrial Technology > Metallurgical Industry > Ironmaking > Blast furnace operation > Dust removal of blast furnace gas
© 2012 www.DissertationTopic.Net  Mobile