Dissertation > Excellent graduate degree dissertation topics show

Hierarchical Porous Carbon as Anode Material for Super Lithium Ion Capacitor

Author: LouShiJu
Tutor: ZhouXiangYang
School: Central South University
Course: Non-ferrous metallurgy
Keywords: Super lithium ion capacitor Lithium ion battery Electric double-layer capacitor Hierarchical pore structure Core-shell structure Carbon anode materials
CLC: TM912
Type: Master's thesis
Year: 2011
Downloads: 180
Quote: 1
Read: Download Dissertation

Abstract


Super lithium ion capacitor (SLIC) is a new kind of energy storage device possessing high energy density as well as high power density. It is very important to develop a new anode material for SLIC. Aiming at obtaining the carbon materials of appropriate pore structure, high reversible capacity and high quality capacitance, in this paper, hierarchical porous carbon was innovatively fabricated as SLIC anode material. A series of hierarchical porous carbon (HPC) were prepared by templating method, and their physical or electrochemical properties were analyzed. Then physical activation-templating method was used to prepare local graphitization hierarchical porous carbon materials (HPGC) with high specific capacitance and high reversible capacity. Finally, in consideration of the large initial irreversible capacity of HPGC materials, CHPGC materials, which are consist of HPGC materials as shells, and CMS (carbonaceous mesophase spherule) as the core were designed and prepared as the anode materials for SLIC, their electrochemical and electrode dynamic properties were also studied intensively. The relative conclusions are as follows:(1) It can be found that HPC-600 (activation temperature is 600℃, alkali/C ratio is 2) exhibits the best electrochemical performance. The specific surface area and average aperture of HPC-600 are 276.2 m2/g and 7.25 nm respectively. It has large initial discharge capacity of 1062 mAh/g and reversible charge capacity of 410 mAh/g, specific quality capacitance of 65 F/g and better circulation performance, however, it’s inevitable to emerge large diffusion resistance and contact resistance.(2) The results indicate that proper porous structure and specific surface area are beneficial to form anode material with higher reversible capacity, better rate performance and higher capacitance. HPGC-800 prepared at 800℃has the highest specific surface area (524.2m2/g) and average aperture of 5.57 nm, but HPGC-600 has the optimal electrochemical performance. The initial discharge capacity of HPGC-600 is 2031.2 mAh/g, and charging capacity is 611.2 mAh/g. After 50 times cycles, the rate of capacity retention is 74%. The reversible capacity at 6C is 225 mAh/g. The specific capacitance is up to 143 F/g and the capacitance rate performance is also great.(3) The capacitance features of CHPGC show that when CMS increases, the capacitance, contact resistance, and the diffusion resistance of CHPGC materials decrease. CHPGC-1 (mass ratio of CMS and phenolic resin is 1) material has the most reasonable shell/core structure and the highest specific capacitance (36 F/g). The battery features show that the initial discharge capacity and charge capacity of CHPGC-1 are 1049 mAh/g and 524 mAh/g respectively. The rate of capacity retention is 90.3% after 50 times cycles.(4) The results of kinetics show that the exchange current density increases, while the lithium ion diffusion coefficient decreases as lithium ion is intercalated into carbon electrode. Among these materials, the minimum exchange current density is HPGC-600, while the maximum is CHPGC-1. Comparing HPGC-600, CHPGC-1, and CMS, lithium ion diffusion coefficient decreases gradually.

Related Dissertations

  1. Preparation and Properties of Silicon Carbon Anode for Lithium Ion Battery,TM912.9
  2. Preparation and Characterization of Carbon Materials as Electrode Materials for Supercapacitor,TM53
  3. Preparation of Silicon-based Alloy Anode Material Andelectrochemical Properties,TM912
  4. Research of Graphitized Needle Coke Coated by Phenolic Resin Pyrolytic Carbon as Anode Material for Lithium Ion Battery,TM912
  5. Preparation and Modification of Lithium Ion Battery LiNi0.8Co0.05O2 Cathode,TM912
  6. Effect of Water Binder on the Electrochemical Performance of Graphite,TM912
  7. Preparation and Performance Research of Lithium Ion Battery Anode Material Li4Ti5O12,TM912
  8. Synthesis and Properties of Spinel Limn2 O4 as Cathode Material,TM912
  9. Study lithium titanate prepared from ilmenite,TM912
  10. Synthesis and Modification of Cathode Materials LiFePO4 and Li2FeSiO4 for Lithium Ion Battery,TM912
  11. Lithium-Ion Battery Equalization System Simulation Study on Bidirectional Flyback DC-DC Converter,U463.633
  12. Supercritical Method Preparation for Lithium Iron Phosphate Nanometer Material and Its Carbon-coating Research,TM912
  13. Research on Functional Electrolytes for Lithium Ion Battery,TM912
  14. Study on the Preparation of Zeolite with Core-Shell Structure and Indirect Synthesis of Cyclohexanol from Cyclohexene,TQ233.1
  15. Synthesis and Modification of Nano LiFePO4 as Cathode Materials,TM912
  16. Study on Synthesis and Modified of LiFePO4 as Cathode Materials,TM912
  17. Preparation and Research Electrochemical Properties of LiFePO4 for Cathode Material of Lithium-ion Batteries,TM912
  18. Porous electrode material of vanadium pentoxide Synthesis, Characterization and Properties,O614.511
  19. Preparation of high surface area activated carbon , forming and preliminary application,TQ424.1
  20. Graphite anode low temperature performance influencing factors and improving research,TM912
  21. New lithium -ion battery anode material Li 4 Ti 5 O 12 Preparation and Modification,TM912

CLC: > Industrial Technology > Electrotechnical > Independent power supply technology (direct power) > Battery
© 2012 www.DissertationTopic.Net  Mobile