Dissertation > Excellent graduate degree dissertation topics show

Study of Experiment and Numerical Simulation for Tube vs Plate Explosive Welding

Author: WangHuHe
Tutor: ZuoZuo
School: Inner Mongolia University of Technology
Course: Materials Processing Engineering
Keywords: Tube vs plate explosive welding Numerical simulation Explicit dynamics ANSYS/LS-DYNA
CLC: TG456.6
Type: Master's thesis
Year: 2009
Downloads: 81
Quote: 1
Read: Download Dissertation

Abstract


Large industrial heat exchangers are important equipments in the area of oils and chemical industries. Connections of radiator tube and strongback were key point in the process of heat exchanger. The compression resistence and life-span of Large-scale industrial heat exchangers are directly related to welding quality of tubesheet. The traditional ways connecting the tubesheet are that molten welding,mechanical expansion,mechanical expansion–welding and so on.These methods can expect a certain amounts of connection strength and airtightness, However,the small connection area, the low connection efficiency and the short life-span cannot be achieved the expected compression resistence and the life-span.Tube vs sheet explosive welding technology is a special welding method of high energy rate. Under the correct parameters and process, more than ten even the whole radiator tubes could be welded with the strongback through this method,which reflect the high efficiency and energy saving,high production efficiency and the benefitable connection quality.In this paper,study of tube-sheet explosive welding for three materials were represented after searching and reading relevant knowledges both at home and abroad,the material modle and finite element model are constituted. and finally,large nonlinear finite element analytic software ANSYS/LS-DYNA is used through the process of the simulation of the tube vs sheet explosive welding.Experimental result and simulation result show that:1、Explosive welding method can successfully achieve the metallurgical bonding of the copper tube-steel plate、the stainless steel tube-steel plates and the steel tube-steel plate,their bonding area were perfect microwaves. The technology provides a energy-saving and efficient approach.for the manufacture of heat exchangers tube plate connection.2、The existing formula for calculating dynamite amount of tube vs plate explosive welding were amended through the experimental results;3、Numerical simulation results show that: The composite energy of the point of near initiation is lower than that of stable detonation,so the boundary effect of the process of explosive welding is appeared.According to what we have obtained, the process of removing the boundary effect was set down.4、Error between the theoretical calculation results and simulation results of the collision piont pressure and flyer tube velocity were no more than 5%,reflecting the good matchness of between the result and the simulation.,which could be advised in the industry.5、The stress state,the jet character and bonding form of waveform.are reasonable reflected by Simulation results during explosive welding.

Related Dissertations

  1. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  2. Study on Springback of High-Strength Steel Stamping,TG386
  3. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  4. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  5. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  6. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  7. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  8. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  9. Numerical Simulation of SNCR Process of a 600MW Utility Boiler,TK222
  10. Numerical Simulation of Biomass Direct Reburning,TK16
  11. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  12. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  13. Study on Gas-Solid Two-Phase Flow in Spouted Beds,TK173
  14. Experimental Study and Numerical Simulation on Aerodynamic Field of Tangential Bias Swirl Burner,TK223.23
  15. Characteristic Study of Combustion in Central Reverse Flame Chamber,TK223.21
  16. Numerical Simulation and Contrastive Analysis of Labyrinth Seals and Leaf Seals,TK263.2
  17. Numerical Study on Phosphorus Distribution in Water Environment of the Three Gorges Reservoir,X832
  18. The Design and Performance Simulation of External Valve Small Displacement Pump,TE933.3
  19. Analysis of the Impact of Tailings Dam Stability under Seepage Role,TV649
  20. Study on Hydraulic Fracturing of Low Permeability Reservoir,P618.13
  21. Numerical Simulation and Experimental Study of Air-Assisted Sprayer of Orchard,S491

CLC: > Industrial Technology > Metallurgy and Metal Craft > Welding, metal cutting and metal bonding > Welding process > Special welding > Explosive Welding
© 2012 www.DissertationTopic.Net  Mobile