Dissertation > Excellent graduate degree dissertation topics show

Punching Shear Capacity Analysis of Concrete Slab Based on the Three-parameter Unified Strength Theory

Author: HanXiangLi
Tutor: ZhaoJunHai
School: Chang'an University
Course: Structural Engineering
Keywords: Three-Parameter Unified Strength Theory reinforced concrete slab unbonded pre-stressed reinforced concrete slab punching shear finite element analysis
CLC: TU312.1
Type: Master's thesis
Year: 2011
Downloads: 80
Quote: 0
Read: Download Dissertation

Abstract


So far, the flat-plate structure has been widely used in multi-storey factory buildings, warehouses, the public buildings halls as many advantages. However, slab-column connections in plate structures came to bear a larger concentration from plate. Thus the connections are susceptible to punching shear failure, Since punching shear failure is a typical brittle failure, it will cause the separation of slab and column and might even cause progressive collapse of the whole structure. Many researches have been focused on this problem.In this paper, Punching shear capacities have been investigated for reinforced concrete slab and the unbonded pre-stressed reinforced concrete slab based on the three-parameter unified strength theory, The numerical models have also been established and the punching shear capacities have been simulated using finite element simulation. The main contents are listed as follows:In this paper, some common codes and the analysis methods for punching shear of the concrete plate have been reviewed firstly. The punching shear failure mechanism has been analysed. The main factors influcing the punching shear capacities have been studied according to previous literatures and the failure process.The flexural capacities for the concrete circular and square plate have been obtained based on yield line theory. The punching strength of the reinforced concrete slab is then analyzed in this paper based on the three-parameter unified strength theory. The problem is treated as a three-dimensional axisymmetrical one, the material being assumed to be rigid-plastic. The formula of the punching strength for reinforced concrete slab is derived. Based on the above work, the ultimate punching shear strength of the unbonded pre-stressed reinforced concrete slab is obtained by being equivalent the effective pre-stress to the external forces acting on the plate.The punching shear performance on the above two types of plate is simulated using the commercial finite element software ANSYS. The crack development situation and the punching shear capacities of slab are obtained. Parametric studies have been carried out to investigate the influences of concrete strength, the reinforcement ratio, different way of pre-stressed reinforcement. Good agreement can be observed by comparison with test data.

Related Dissertations

  1. Research on the Mainframe System of Powder Mixed EDM and the Craft Experiment,TG661
  2. EDM Electrode Wear Mechanism and Control Research,TG661
  3. Finite Element Analysis and Structure Optimal Design for Combined Seal at Normal Temperature and Low Temperature,TH136
  4. Study on the Design and Biomechanical Behaviors of Individualized Artificial Knee Joint,R318.1
  5. Design of Testing Equipment for Electronic Products,TN06
  6. Multi-pin Internal Fixation of Calcaneal Fractures in Finite Element Analysis,R687.3
  7. Airborne radar antenna pedestal rapid design systems research and development,TN959.73
  8. Sham hose drum drive means and hydraulic system of the structure,TE973
  9. The magnetorheological damper mechanical properties and Gun Recoil,TB535.1
  10. Nonlinear Structural Dynamics Analysis and Optimization Design on Naval Gun Driver,TJ391
  11. Design and Analysis of Automatic Steel Pipes Butt Tool,U673.38
  12. Analysis on Unloading of Large Span Steel Structures and Research on Its Mechanical Analysis,TU391
  13. Study on Virtual Simulation Technology of Safety Valves Based on SolidWorks,TH134
  14. Optimized Design of New Style Mast of ZJ50L Drill Rig,TE923
  15. The Structure Design and Finite Element Analysis for the Light Hydraulic Support with Auxiliary Beam,TD355.4
  16. Analysis on Static-dynamic and Fatigue Characteristics of Metallurgical Overhead Traveling Crane,TH215
  17. Research of Deep Excavation Construction Process for Nearby Subway Section Action,TU753
  18. Study on Geometric Characteristics and Fininte Element Anslysis of Hositing Ropes,TD532
  19. Analysis of Gray Cast Iron Cutting Factors and Reasonable Choice of Tools,TG506
  20. Expandable screen -based research and effective performance analysis TWIP steel,TF762
  21. Research on Computerized Double Cylinder Hosiery Machine’s Looping Mechanism Based on Element Finite Analysis,TS183.5

CLC: > Industrial Technology > Building Science > Building structure > Structure theory to calculate > Structural loads and structural capacity > Structural load analysis
© 2012 www.DissertationTopic.Net  Mobile