Dissertation > Excellent graduate degree dissertation topics show

Influence of Rolling and Cooling Processes on Microstructures and Mechanical Properties of 500MPa Steel Strip for Automobiles

Author: ZhangWuBin
Tutor: LiuYunZhong；MaoXinPing
School: South China University of Technology
Course: Mechanical Engineering
Keywords: rolling and cooling processes microstructures mechanical properties influence
CLC: TG335.5
Type: Master's thesis
Year: 2010
Downloads: 87
Quote: 0
Read: Download Dissertation

Abstract


High-strength strip production is one of advantages of the thin slab casting and rollingproduction line. So it is a practical application to produce high-strength auto-used 550MPastrips with V-N micro-alloying by this process. During developing these new steel varieties,the influences of controlled rolling and controlled cooling (TMCP) processes includingheating temperature, reduction rate, rolling temperature, coiling mode, coiling temperature ontheir microstructures and properties were studied in detail in this work. The main conclusionsare as follows.(1) The influence of heating temperature on microstructures and properties of 550MPastrips for automobiles was studied. For the thick V-N micro-alloyed 550MPa automobile steelstrips, when the heating temperature reach to 1100℃, the transverse yield strength is 20MPahigher, the impact toughness at -20℃is 20J higher, and the average grain size is 1.1μmsmaller than that at the heating temperature 1130℃.(2) The influence of rolling temperature on microstructures and properties of 550MPastrips for automobiles was studied. When the rolling temperature is 820℃, the yield strengthis 40MPa higher, the elongation rate is 10% lower, the average grain size is almost sameness.But the cold bending property is not qualified at this rolling temperature. Meanwhile, thereare a lot of acicular ferrites in the microstructure.(3) The influence of reduction rate on microstructures and properties of 550MPa stripsfor automobiles was studied. When the accumulative reduction rate increases 9%, the yieldstrength is 20MPa higher, the elongation is 4% lower, the average grain size is almostsamensee.(4) The influence of coiling mode on microstructures and properties of 550MPa stripsfor automobiles was studied. Different cooling modes have different cooling rates. Themaximum continuous cooling rate at the tail reaches 65.9℃/s. The minimum interval coolingrate at the head reaches 37.1℃/s. Different cooling modes have little effects on themicrostructures and properties of 550MPa automotive steel strips.(5) The influence of coiling temperature on microstructures and properties of 550MPastrips for automobiles was studied. Compared with the coiling temperature 600℃, when coiling temperature is 550℃, the yield strength is 12.5MPa lower, the elongation is 1.25%higher, the average grain size is almost sameness , and the transverse impact toughness at alow temperature -20℃is 13.4J lower, and the longitudinal one is 14.3J lower.

Related Dissertations

  1. Reactive Hot-Pressing and Mechanical Properties of （ZrB2-ZrO2）/BN Composites,TB332
  2. Research on Welding Characteristics of CO2 Laser-GMA Hybrid Welding for Ultra-Low Carbon Bainitic Steel,TG456.7
  3. Microstructure and Mechanical Properties of Mg-Zn-Y-Zr Alloys,TG146.22
  4. Development of Turbine Rotor Dynamic Balance System,TH877
  5. Research on the Correlation between Formative Assessment in College EFL Class and Students’ Learning Attitude,H319.3
  6. Study on the Recycling of Post-Consumer Polyester Textiles,X791
  7. Broiler Responses to Reduced-protein Diets Suppleme Nted with Synthetic Amino Acids and Small Peptides,S831.5
  8. The Study in the Influence of the Cell Phone on the Moral Values of the College Students and the Countermeasure,G641
  9. Fabricationand Properties of SiC-AlN Multiphase Ceramics Prepared by Gelcasting,TQ174.62
  10. Synthesis of Polysulfones and Modification for Epoxy Adhesives,TQ433.437
  11. Research on the Regional Difference and Influence Factors of China’s Carbon Emissions,X502
  12. Research on Values of Post-90 Generation under the Influence of the Current Pop Culture,C913.5
  13. Research on Present Situation and Influence Factors about Young Chrendren’s Tennis in Xi’an,G845
  14. Network language surveys and studies of vocational school students' language usage,G715
  15. Study on the Rural Left-behind Children’s Studies Question and Its Factors Based on the Case of Min-le Middle School of Conghua, Guangzhou,G521
  16. The Influence of the Primary School Class Cadres’ Selection Mode on the Students’ Democratic Participation Ability,G625.1
  17. The Research of Concrete Shrinkage and Creep Experiment,TU528
  18. Brezhnev period of Soviet oil and gas industry development and its impact,F416.22
  19. Spatial Analysis and Pollution Evaluation about Water Environment Actuality of Rural Surface Water in Typical Regions of Jiangsu Province,S271
  20. The Diagnosis of Modernity of Marx to Enlighten to Human’s Development,A811
  21. Research of Chinese Official Think Tanks Affect Government Decision,D630

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metal pressure processing > Rolling > Rolling process > Sheet, strip,foil rolling
© 2012 www.DissertationTopic.Net  Mobile